User manual LINKSYS EF1324 Install Guide

[. . . ] Instant EtherFast® Series EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch Use this guide to install: EF1324 User Guide EC Declaration of Conformity (Europe) In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive 93/68/EEC, this product meets the requirements of the following standards: · EN55022 Emission · EN55024 Immunity Industry Canada (Canada) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe (B) est conforme à la norme NMB-003 du Canada. COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. EtherFast, Linksys, and the Linksys logo are registered trademarks of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. [. . . ] IGMP snooping is used to monitor for any attached hosts who want to receive a specific multicast service. It looks up the IP Multicast Group used for this service and adds any port that received a similar request to that group. (This is the screen and options displayed for a Switch in multilayer mode. ) · Index Server Address - Used to define any preferred DHCP servers or the outbound subnetwork for relaying a DHCP request broadcast. (Up to five entries are permitted. ) Select OK to return to the previous panel. Add BOOTP Relay Server The Add BOOTP Relay Server screen allows you to add an entry. · · IGMP Router Timeout - A switch port that stops receiving multicast protocol packets for this interval will be removed from the IGMP forwarding list. IGMP Group Timeout - The time between last spotting an IGMP Report message for an IP multicast address on a specific port and the Switch removing that entry from its list. Select Cancel to cancel any changes. · IP Address - IP address of server. Select OK to return to the previous panel. Select Cancel to cancel any changes. 70 71 Instant EtherFast® Series EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch Static ARP Table The Static ARP Table screen is used to specify the static Address Resolution Protocol. Add Static ARP Entry The Add Static ARP Entry screen is used to add a static ARP entry. · · IP Address - IP address statically mapped to a physical MAC address. · MAC Address - MAC address statically mapped to the corresponding IP address. · Interface - The index number of the IP interface that will use this static ARP entry. To display a specific page, set the page number in the Page field and then press Apply. · IP Address - IP address statically mapped to a physical MAC address. MAC Address - MAC address statically mapped to the corresponding IP address. Interface - The index number of the IP interface that will use this static ARP entry. (Port "0" refers to the CPU. ) · Select OK to return to the previous panel. Select Cancel to cancel any changes. 72 73 Instant EtherFast® Series EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch Static Route Table The Static Route Table screen is used to configure a static route. Add Routing Entry The Add Routing Entry screen is used to add a routing entry. · Destination Network - A destination network, subnet, or host. · Destination Mask - The subnet mask that specifies the bits to match. A routing entry will be used for a packet if the bits in the address set by the destination mask match the destination network. · VLAN - The VLAN within which the gateway or destination address resides. Direct - A directly connected subnetwork Indirect - A remote IP subnetwork or host address Myself - A switch IP address on a specific IP subnetwork Bcast - A subnetwork broadcast address Mcast - An IP multicast address Invalid - An illegal IP address to be filtered Select Apply to make changes. To display a specific page, set the page number in the Page field and then press Apply. [. . . ] SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol. Data is passed from SNMP agents, which are hardware and/or software processes reporting activity in each network device (hub, router, bridge, etc. ) to the workstation console used to oversee the network. The agents return information contained in a MIB (Management Information Base), which is a data structure that defines what is obtainable from the device and what can be controlled (turned off, on, etc. ). STP (Spanning Tree Protocol) - A technology that checks your network for any loops. [. . . ]