User manual LIFT-MASTER TCG2

[. . . ] Patent Pending SPECIFICATIONS Output Rating: 5 Amps 28VAC or DC Max. Power: 12VDC or 18 to 34VAC/DC, @ 30ma RF Frequency: 300 or 310MHz Accessory Transmitters: TC1, TC2 and TC4 Antenna Extension Kit: TCEXT This device complies with FCC Rules Part 15 and IC Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] Unless using maximum number of codes the following four codes should not be used: · All DIP Switches ON · All DIP Switches OFF · DIP Switches alternating ON/OFF · DIP Switches alternating OFF/ON. Step 1 Power Supply Selection Setting The TriCodeTM receiver is factory set for 24 volt power input if 12 volt is required. Remove front cover of receiver by turning screws counterclockwise a 1/4 of a turn until each releases. Set jumper (P3) to either 12 or 24 volt setting depending on your power input (Refer to figure 1). Step 2 Setting Output Relay Mode The TriCodeTM receiver is factory set for momentary relay output "MNT". (a) Momentary mode: The output relay will be on for . 5 seconds before turning off. (b) Constant pressure mode: Output relay is continuously on while receiving matching/valid ID code from transmitter. The output relay will turn off immediately once receiver does not received a matching/valid ID code from the transmitter. If constant pressure mode is desired, move mode jumper from "MNT" to "CST" (Refer to figure 1). NOTE: The relay output is an isolated normally open contact. Receivers should be installed at least 5 feet apart to avoid cross-talk. After completing installation, operate transmitter outside of building to make certain the chosen DIP switch setting does not operate with nearby garage door operators and/or security systems. If so, select another DIP switch setting and check the coded signal again. Repeat as necessary. RECEIVER MOUNTING Mount receiver to wall using #6 hardware (Not Supplied). ANTENNA MOUNTING Screw on antenna clockwise and slide rubber boot down to meet o-ring. FIGURE 1 RELAY CH1-MODE CH1 MODE CST MNT RELAY CH2-MODE CST MNT CH2 MODE MOUNTING HOLES (4 CORNERS) JUMPER (P3) 12V P3 24V 24V AC/DC CH1 N/O CH2 N/O 2 CONFIGURATION & DIP SWITCH SETTINGS Step 3 Setting the Configuration Switch The TriCodeTM receiver is factory set for Linear/Delta3TM. [. . . ] TM Multi TM: works with all "Multi-Code " transmitters transmitted at 300 MHz using 10-bits ID system. TM StanleyTM: works with all "Stanley radio" transmitters transmitted at 310 MHz using 10-bits ID system. TM FIGURE 2 FIGURE 3 CONFIGURATION SWITCH DELTA-3/ LINEAR MULTI-CODE STANLEY TM TM TM 310 MHz 300 MHz 310 MHz MULTI/ STANLEY (1 THRU 10) LINEAR/ DELTA-3 (1 THRU 8) 1 2 3 4 5 6 TM TM DIP SWITCH O N O F F 7 8 9 10 FIGURE 4 DIP SWITCHES CHANNEL 2 DIP SWITCH CHANNEL 1 DIP SWITCH CONFIGURATION SWITCH DELTA-3/LINEAR MULTI-CODE TM TM STANLEY TM 24V AC/DC CH1 N/O CH2 N/O 3 POWER CONNECTIONS Step 5 Power Supply Connections A prewired gasketed pigtail is included for your convenience (See figure 5 for outgoing wires). NOTE: For internal wire connections refer to figure 6. FIGURE 5 24V AC/DC CH1 N/O CH2 N/O WIRE ENTRY RED BLACK WHITE/GREEN STRIPE WHITE/YELLOW STRIPE BLUE/BROWN STRIPE BLUE/ORANGE STRIPE FIGURE 6 RED POWER SUPPLY 12V/24V BLACK WHITE/GREEN CH1 N/O 24V AC/DC WHITE/YELLOW BLUE/BROWN CH2 N/O BLUE/ORANGE 01-17469C © 2000, The Chamberlain Group, Inc. [. . . ]