User manual LIFT-MASTER T

[. . . ] 2. 0) INDUSTRIAL DUTY DOOR OPERATOR L PATENT PENDING C O N TR O L FACTORY SET C2 Wiring See pages 15 and 16 for other wiring configurations The Maintenance Alert System TM allows the installer to set an internal Maintenance Cycle Counter. An LED on the 3-button station will signal when the set number of cycles is reached or when the opener requires immediate service. 2 YEAR WARRANTY NOT FOR RESIDENTIAL USE Serial # (located on electrical box cover) Installation Date Wiring Type LISTED DOOR OPERATOR 41B6 Before attempting to install, operate or maintain the operator, you must read and fully understand this manual and follow all safety instructions. These instructions are intended to highlight certain safety related issues. Because each application is unique, it is the responsibility of the purchaser, designer, installer and end user to ensure that the total door system is safe for its intended use. TABLE OF CONTENTS SPECIFICATIONS Packing List . [. . . ] Read the descriptions of the different wiring types to determine which setting will be correct for each application. Set the dip switches to the desired wiring mode: Adjust the 4 dip switches on the logic board to match the settings for the desired wiring type. The dip switches are shown in the picture TYPE STATION C2 1 2 3 4 ON ON C2 3 Button, 3 Button Radio Control Function: Momentary contact to open and stop with constant pressure to close, open override plus wiring for sensing device to reverse. Programmable mid stop available with this wiring type. OFF ON ON B2 1 2 3 4 B2 3 Button, 1 Button, 1 & 3 Button Radio Control Function: Momentary contact to open, close and stop, plus wiring for sensing device to reverse and auxiliary devices to open and close with open override. Programmable mid stop available with this wiring type. OFF ON ON D1 1 2 3 4 D1 2 Button, 3 Button Radio Control Function: Constant pressure to open and close with wiring for sensing device to stop. OFF E2 3 Button Radio Control Function: Momentary contact to open with override and constant pressure to close. Release of close button will cause door to reverse (roll-back feature) plus wiring for sensing device to reverse. ON ON E2 1 2 3 4 OFF TS 3 Button, 1 Button, 1 & 3 Button Radio Control Function: Momentary contact to open, close, and stop with open override and Timer To Close. Every device that causes door to open, including a reversing device, activates the Timer To Close. Auxiliary controls can be connected to open input to activate the Timer To Close. If the timer has been activated, the open button and radio control can recycle the timer. The stop button will deactivate the Tim er To Close until the next command input. The Timer To Close will function from the programmable mid-stop with this wiring type. (NOTE: Requires Optional self monitoring photo eyes to operate. ) 15 ON ON TS 1 2 3 4 OFF WIRING TYPE PROGRAM SETTINGS CONT'D TYPE STATION T 3 Button, 1 Button, 1 & 3 Button Radio Control Function: Momentary contact to open, close, and stop, with open override and Timer To Close. Every device that causes the door to open, except a reversing device, activates the Timer To Close. Auxiliary controls can be connected to open input to activate the Timer To Close. If the Timer To Close has been activated, the open button and radio control can recycle the timer. The stop button will deactivate the timer until the next command input. The Timer to Close will function from the programmable mid-stop with this wiring type. (NOTE: Requires Optional self monitoring photo eyes to operate. ) FSTS Momentary button contact for open, close and stop. The single button station opens the door to the full open limit bypassing the mid stop and activates the Timer To Close, putting the operator in TS mode until the door reaches the down limit, or is stopped in travel. (NOTE: Requires Optional self monitoring photo eyes to operate. ) ON ON T 1 2 3 4 OFF ON ON FSTS 1 2 3 4 OFF ON ON C2 FAIL SAFE 1 2 3 4 C2 Failsafe 3 Button, 3 Button Radio Control Same functions as C2. See Self Monitoring Safety Device Options below. OFF ON ON B2 FAIL SAFE 1 2 3 4 B2 Failsafe 3 Button, 1 Button, 1 & 3 Button Radio Control Same functions as B2. See Self Monitoring Safety Device Options below. OFF ON ON D1 FAIL SAFE 1 2 3 4 D1 Failsafe 2 Button, 3 Button Radio Control Same functions as D1. [. . . ] Lubricate Check set screw tightness Check & adjust as required Check condition & tension Check & tighten as required EVERY 3 MONTHS OR 5, 000 CYCLES EVERY 6 MONTHS OR 10, 000 CYCLES EVERY 12 MONTHS OR 20, 000 CYCLES l l l l l l l t t t t t t t Sprockets Clutch Belt Fasteners Manual Disconnect Check & Operate Bearings & Shafts Check for wear & Lubricate S Use SAE 30 Oil (Never use grease or silicone spray). n Inspect and service whenever a malfunction is observed or suspected. n CAUTION: BEFORE SERVICING, ALWAYS DISCONNECT OPERATOR FROM POWER SUPPLY. HOW TO ORDER REPAIR PARTS OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION ARE AVAILABLE 6 DAYS A WEEK CALL OUR TOLL FREE NUMBER - 1-800-528-2806 MONDAY THROUGH FRIDAY 5 A. M. TO 6 PM (MST) SATURDAY 7 AM TO 3:30 PM (MST) WWW. LIFTMASTER. COM WHEN ORDERING REPAIR PARTS PLEASE SUPPLY THE FOLLOWING INFORMATION: PART NUMBER DESCRIPTION MODEL NUMBER 23 ILLUSTRATED PARTS - ELECTRICAL BOX S7 S1 S3 S6 S5 S2 S8 S4 S9 10 5 L3 L1 L7 L9 6 7 L8 L5 4 8 9 L8 L6 L2 L2 L6 L4 2 4 1 3 24 REPAIR PARTS KITS ­ ELECTRICAL BOX LOGIC CONTROL (VER. [. . . ]