User manual LIFT-MASTER SW2000

[. . . ] ESTATE SERIES X3 MODEL SW 2000-X3 INSTALLATION MANUAL HEAVY DUTY, HIGH CYCLE SWING GATE OPERATOR MODEL SW 2000-X3 IS FOR VEHICULAR PASSAGE GATES ONLY, NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE 3 YEAR WARRANTY Serial # _____________________ (located on electrical box) Installation Date ______________ TABLE OF CONTENTS SAFETY SUMMARY ___________________________________________________________________1 BASIC INSTALLATION HINTS AND RULES ______________________________________________2 PART 1 SITE PREPARATION __________________________________________________________3 A. LOCATION AND LAYOUT ________________________________________________________________ 3 B. PAD AND MOUNT _______________________________________________________________________ 4 C. POWER WIRING_________________________________________________________________________ 5 D. [. . . ] Wire all external control devices to their connections on the control board as shown. See Appendix A for details on how each control input affects the gate operator. Connect the Master/Slave interconnect cable (see Master/Slave Systems for X3 Series Gate Operators, Part 1). Disconnecting the STOP terminal from the COMMON terminal stops the gate and prevents all commands from having any effect. IMPORTANT: As per UL325 standards, install the Manual Input and Fire switches in the line of sight with the gate. If gate(s) are used for bi-directional traffic, the Exit Loop should be a directional loop detector. Inside and Outside Interrupt Loops: For maximum safety, Inside and Outside Interrupt loops require separate loop detectors. Bi-part or Bi-part Latch: If only one loop detector is used, connect Outside loop to the Inside loop detector. Battery is used to store date and time. 16 of 42 Doc 01-20099 Rev F L. BASIC GATE OPERATOR PROGRAMMING Even if you plan to program the gate operator by telephone, you may want to enter some immediate instructions during installation. The following list of instructions will help you set basic controls so the gate will operate properly until you have time for full programming, either directly or by telephone. For complete programming instructions, refer to "SL 1000, SW 2000, and BG 3000-X3 Programming (-173 bd)". To access programming mode: enter QQQ 000000 (3 asterisks, 6 zeroes) To program a command: a) enter step number b) enter required data c) enter # (pound sign) To exit programming mode: enter 00# (2 zeroes, 1 pound sign) Step 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Gate Type Purpose Step 1 1 1 1 3 Up to 3 Up to 3 Up to 3 Up to 3 Up to 3 6 Operator Type Pair Type Not Used Not Used Anti-Tailgate Enable (ATG) Latch Delay Time Reclose Time (RT) Not Used Not Used Obstruction Sense Backup Closing Obstruction Sense Backup Opening Interrupt Bar Backup If Closing Interrupt Bar Backup If Opening Return to Factory Set Defaults Default Acceptable Input 1 0 = Slide, 1 = Swing, 2 = Barrier, 3 = Linear 0 0 = Single, 1 = Master, 2 = Slave 0 0=Bipart, 1=Latch, 2=Not Used, 3=Tandem 0 0 = Disabled, 1 = Enabled 6 0 ­ 250 Seconds (. 4 sec. Increme nts) 30 0 ­ 250 Seconds (0 = Disabled) 12 12 ­ 499 Inches See note below. · 12 12 ­ 499 Inches See note below. · 12 12 ­ 499 Inches See note below. · 12 12 ­ 499 Inches See note below. · N/A 101010 (partial), 191919 (full) · IMPORTANT NOTE: SWING GATE BACKUP DISTANCES Slide gates move at about one foot per second, so backup distances (Obstruction Senses and Interrupt Bar Backup) are easy to enter. Swing gates, however, move in degrees per second, so it is the length of the gate that determines how far the gate moves each second. For instance, a twenty foot gate will move twice as far as a ten foot gate in the same amount of time. As a result, entering backup distances for swing gates is different than for slide gates. Use the following table to enter swing gate backup distances: I want my gate to move this far out at the end: One foot Two feet Three feet And my gate length is: 15' 20' Enter 6" Enter 3" Enter 12" Enter 6" Enter 18" Enter 9" 10' Enter 9" Enter 18" Enter 27" Rev· F Doc 01-20099 17 of 42 M. Verify that switch S2 (the Gate Open Direction switch) is set to the correct position. Verify that Manual Open fully opens the gate and that the open limit switch stops the gate. Verify that Manual Close fully closes the gate and that the close limit switch stops the gate. Note: If the gate stops due to an obstruction Fault, readjust the gate sensitivity pots. Gate Sensitivity and Obstruction Alarm (Primary Obstruction Sensing per UL 325 Requirements) 1. [. . . ] DISCONNECTION If you should ever decide to permanently disconnect your operator from its present line, please call the telephone company and let them know of this change. RADIO FREQUENCY This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ]