User manual LIFT-MASTER STAR250

[. . . ] STAR250TM WIRELESS ACCESS CONTROL RECEIVER SPECIFICATIONS SUPPLY VOLTAGE: 12-24 VOLTS AC OR DC OPERATING CURRENT: 250 mA MAXIMUM OPERATING TEMP RANGE: -40 TO +149F (-40 TO +65C) FREQUENCY: 390 MHz RELAY CONTACT RATING: 1 AMP @ 24 VOLTS AC OR DC This device complies with FCC Rules Part 15 and IC Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] If this is unavoidable, we recommend installing the antenna extension kit (86LM) for best results. Receiver Mounting: Mount Backplate to desired surface using #6 hardware (Not provided). Direct Antenna Mounting: Install the supplied antenna onto the STAR250 antenna connector by screwing the connector clockwise. Slide the seal boot down to meet the O-Ring, covering the antenna hardware. Remote Antenna Mounting: Use the optional 86LM antenna extension kit to mount the remote antenna as high and far from metal as possible for best radio range (Figure 2). Contact LiftMaster customer service at: 1-800-528-2806 to order the model 86LM. Figure 1 Antenna Seal Boot Antenna Connector Figure 2 STAR250 FEATURES PROGRAMMING THE STAR250 Rapid LearnTM- Add transmitter to next available location. Adding Transmitter- Add transmitter to a specific location. Deleting a Transmitter- To delete a user. 2 PROGRAMMING THE STAR250 (CON'T) Blocking (Unblocking) a Transmitter- To block or unblock a user. Duplicating Memory- Allows user to back up learned transmitter memory into the provided backup memory module. dup , PRESS SIMULTANEOUSLY Main Memory Module END * 6 ~6 SECONDS Backup Memory Module NOTE: To duplicate memory, plug memory module into back up slot and press *, 6. Once duplication is complete, remove the backup memory module and store in a separate location. Restoring Memory- To restore memory, simply place the duplicate memory module from the backup memory location in the main memory position. For advanced functions, press and hold the (*) key and a number key at the same time to select the corresponding advanced function. (See table at right for available functions. ) Press the `#' key to exit the function. AUDIBLE DIAGNOSTICS Step 1. (LED will be displayed when OFF) Double Beep- Transmitter is valid & learned into STAR250accompanied by transmitter location display. Triple Beep- Confirmation of Delete. KEYPAD SOUND ALERTS Single Beep- Key Pressed. [. . . ] If unit exhibits this condition again after 2 minutes, contact Technical Service ELECTRICAL CONNECTIONS FOR STAR250 Receiver (Bottom) Wall Button Receiver (Bottom) Wall Button Opener Trans Primary Trans Primary Model 85 Transformer To wall outlet To wall Model 95 outlet Transformer STAR250 COMPATIBLE TRANSMITTERS Billion Code Transmitters 81LM 82LM 83LM 84LM STAR250 OPTIONAL ACCESSORIES CGI Part Number 71-65WTBOX 86LM 85LM 95LM Security+ Transmitters 91LM 92LM 96LM 970LM 971LM 972LM 973LM 974LM Description Watertight Box Field Install Kit Antenna Extension Kit 24VAC transformer w/barrel connector 24VAC transformer w/screw terminals Billion Code Keypads 66LM 466LM Passport Transmitter CPT4 Security+ Keypads 67LM CPT1 976LM CPT2 CPT3 For highest level of security, we recommend the Security+ transmitter family. HOW TO ORDER REPAIR PARTS OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION ARE AVAILABLE 6 DAYS A WEEK CALL OUR TOLL FREE NUMBER - 1-800-528-2806 MONDAY Through FRIDAY 5:00 a. m. (MST) WWW. LIFTMASTER. COM 01-18513C ©2005, The Chamberlain Group, Inc. [. . . ]