User manual LIFT-MASTER SL585

[. . . ] GL CO NT RO LL ER BO AR D HEAVY DUTY SLIDE GATE OPERATOR MODEL SL585 MODEL SL595 2 YEAR WARRANTY Serial # ________________________ (located on electrical box cover) Installation Date __________________ HEAVY DUTY, HARSH ENVIRONMENT SLIDE GATE OPERATOR MODELS SL585 AND SL595 ARE FOR VEHICULAR PASSAGE GATES ONLY AND ARE NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory . . 4 IMPORTANT NOTES · BEFORE attempting to install, operate or maintain the operator, you MUST read and fully understand this manual and follow all safety instructions. · DO NOT attempt repair or service of your commercial door and gate operator unless you are an Authorized Service Technician. OPERATOR WARNINGS Safety Installation Information . . 20 CAUTION WARNING WARNING Electrical WARNING CAUTION When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of SERIOUS INJURY or DEATH if you do not comply with the warnings that accompany them. [. . . ] Activation of this input for longer than three seconds will enable the control to be used as a constant pressure override device. This will allow the user, in emergencies, to override a failed accessory such as a loop detector or photo-eye. Terminals 4 & 5 (Com) - Close Override Control Input These terminals are intended for use only with the close control of a 3-button station that is installed within line of sight of the gate. Activation of this input for longer than three seconds will enable the control to be used as a constant pressure override device. This will allow the user, in emergencies, to override a failed accessory such as a loop detector or photo-eye. Terminals 8 & 5 (Com) - Interrupt (Safety) Loop Input These terminals are intended for use with a loop detector. Terminals 2 & 5 (Com) - Shadow Loop Input These terminals are intended for use with a loop detector and is primarily used on swing gate operators. This input protects cars by preventing the gate from moving off of the open or close limit when the shadow loop input is active. Commands are seen when +24Vdc is applied to the controller's input terminals. NOTE: The control board has built in surge suppression circuitry however please take precautions when adding any additional surge protection. MASTER/SECOND SYSTEMS Dual Gate Communications The control board is capable of running the operator in a master or second mode depending on (S4) switch setting. Before initiating any command the master unit queries for the presence of a "second unit" for a time period of one second. If the master gets no response the operator will operate in a stand alone mode. NOTE: For single unit applications, a jumper must be placed between 11 and 12 of the field wiring terminal block. If the master detects the presence of a second unit the master will continue to query the second unit during travel. The second operator will stop if there is a period of one second or more of no communications. When two operators are connected in dual gate configuration accessories may be connected to either the master or second. NOTE: Do not run Master/Second communication wiring in the same conduit as the power and control wiring. The Second unit will require a normally close stop circuit for proper system operation. After Master/Second wiring has been completed and the S4 switch programmed, both units must have their power cycled to initiate proper Master/Second communication. The motor learn function must be completed in stand alone mode prior to Master/Second wiring. 19 Hard Open Override Control Input 34 56 789 N. O. Com 3 4 5 7 8 8 Close Override Control Input 1 234 567 1 2 3 4 5 6 N. O. Com 1 23456789 1 23456 Shadow Loop Input Interrupt (Safety) Loop Input Master or Standalone Gate Setting Master Unit ON Second Gate Setting Master Unit ON S4 S4 Second Unit Second Unit Terminal Block 12 11 Interrupt Safety Loop STREET Terminal Shielded Block 11 12 cable (twisted pair) minimum 18 gauge Conduit Ground Master pt rru p Inte ty Loo COMPLEX fe Sa OR PARKING LOT 6' Second SEQUENCED ACCESS MANAGEMENT SYSTEM (SAMS) The Sequenced Access Management System or SAMS allows the customer more control when managing vehicular entrances to areas such as apartment complexes, businesses and gated communities. [. . . ] Mounting Channel - 5' (1. 5 m) long Miller MGR20 2-wire electric edge in 5' (1. 5 m) lengths for 2" (5 cm) round post. Miller MGR20 2-wire electric edge in 5' (1. 5 m) lengths for 2" (5 cm) square post. VOLTAGE +24V ac/dc +24V ac/dc 36 NOTES 37 WARRANTY LIFTMASTER® TWO YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the final purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of two years from the date of purchase. [. . . ]