User manual LIFT-MASTER SL575

[. . . ] CO NT RO LL ER GL BO AR D MODEL SL575 HEAVY DUTY SLIDE GATE OPERATOR 2 YEAR WARRANTY Serial # ________________________ (located on electrical box cover) Installation Date __________________ MODEL SL575 IS FOR VEHICULAR PASSAGE GATES ONLY AND IS NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory . . 4 WARNING Mechanical OPERATOR WARNINGS Safety Installation Information . . 8 CAUTION WARNING WARNING Electrical WARNING CAUTION When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of SERIOUS INJURY or DEATH if you do not comply with the warnings that accompany them. When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your gate and/or the gate operator if you do not comply with the cautionary statements that accompany it. [. . . ] See owner's manual for wiring distances and wire gauge information. WARNING: All controls that are to be used to operate the gate system, must be installed where the user cannot come into contact with the gate while operating the controls where the user has full view of gate operation. *We strongly recommend that you follow the UL guidelines presented throughout the manual. Installation device instructions: Always follow the instructions provided by the manufacturer when installing and adjusting any control device. If these instructions are contrary to the advice given here, call for assistance. CLOS E ST OP Interrupt (Safety) Loop Input (N. O) Shadow Loop Input (N. O. ) RF QE RF QE Obstruction While Opening Edge/Photo Eye Input (N. O. ) Radio (Single Button) Input (N. O. ) Obstruction While Closing Edge/Photo Eye Input (N. O. ) 18 ACCESSORY WIRING All inputs are normally open and momentary, except the stop (N. C. ). The following instructions are based upon UL325, and include recommendations for significant increase in safety. We strongly recommend that you follow the UL guidelines presented throughout the manual. Refer to instructions shipped with optional control devices for mounting, wiring, programming and adjustment. 24VAC Accessory Power can be found at terminals R1 and R2 located on radio terminal block. The LiftMaster Radio Receiver comes pre-wired to the Operator · Remove the brass antenna from the accessory box and screw it onto the "F"-connector provided on the side of the gate operator. NOTE: The radio receiver is wired in the factory for single button control to open and close the gate. R1 R2 R3 R4 24VAC RADIO RCVR. Receiver Operator Terminal 4 3 Connector Antenna R4 R3 R2 R1 Relay Control 24VAC Power 2 1 Accessory Tray 1 234567 REMOTELY MOUNTED STOP/RESET CONTROL WIRING · This control will function as a Stop/Reset command and is to be wired within line of sight of the gate. · Wire Stop/Reset control station to terminals 3 and 5 on the control box on the operator. STOP/RESET AUXILIARY CONTROL WIRING Terminals 6 & 5 (Com) - Open These terminals are intended for use as a general open control. Accessories that may be wired to this input include: Telephone Entry Systems, Radio Receiver (Commercial Applications), Exit Loop Detector, Keypads, 7-Day Timer. NOTE: Will not override a double entrapment (signalled by the gate stopped and entrapment alarm on). Control Conduit Control Conduit 1 2 3 Stop/Reset Button Stop/Reset Button 1 234 5 6 7 8 9 10 11 12 13 14 123 56 789 0# Radio (Signal Button) Input 19 R1 R2 R3 R4 ACCESSORY WIRING (CONTINUED) STOP/RESET AUXILIARY CONTROL WIRING (CONTINUED) Terminals 7 & 5 (Com) - Open Override Control Input These terminals are intended for use only with the open control of a three-button station that is installed within line of sight of the gate. Activation of this input for longer than three seconds will enable the control to be used as a constant pressure override device. This will allow the user, in emergencies, to override a failed accessory such as a loop detector or photo-eye. Terminals 4 & 5 (Com) - Close Override Control Input These terminals are intended for use only with the close control of a three-button station that is installed within line of sight of the gate. Activation of this input for longer than three seconds will enable the control to be used as a constant pressure override device. This will allow the user, in emergencies, to override a failed accessory such as a loop detector or photo-eye. Terminals 8 & 5 (Com) - Interrupt (Safety) Loop Input These terminals are intended for use with a loop detector. Terminals 2 & 5 (Com) - Shadow Loop Input These terminals are intended for use with a loop detector and is primarily used on swing gate operators. [. . . ] Please consult a parts and service representative regarding availability of individual components. Complete Electrical Box Replacement Kits: To order a complete electrical box replacement kit add a "K" prefix to the model number of your operator. For Example: SL-575-50-11 (Operator) = K-SL5755011 (Electrical Box) CONTROL BOX ASSEMBLY (K75-18620) ITEM 1 N/S 2 3 4 5 6 7 8 9 10 PART # K001A5566-3 K74-18379 OVERLOAD 312HM K72-34818 13-10024 23-10041-1 03-8024-K 23-34815 21-3260-1 23-30716 DESCRIPTION LOGIC BOARD KIT HALL EFFECT KIT (NOT SHOWN) SEE VARIABLE PARTS LIST RADIO LIMIT SHAFT KIT LIMIT NUT LIMIT SWITCH CONTACTOR OPEN/CLOSE SWITCH TRANSFORMER STOP SWITCH QTY 1 1 1 1 1 1 2 1 2 1 1 4 5 1 2 7 6 3 9 5 8 8 10 VARIABLE PARTS LIST PART MOTOR P/N 20-1050B-2P 20-1100B-2P 20-3050B-4P 20-3050M-5 20-3100B-4P 20-3100M-5 22-120 22-240 22-575 23-20088 23-3005 23-3001 25-2006 25-2008 25-2010 25-4002-SK DESCRIPTION USED ON 1PH 1/2HP BASE MOUNT 115/230V SL575-50-11, SL575-50-21, SL575-50-81 1PH 1HP BASE MOUNT 115/230V SL575-100-11, SL575-100-21, SL575-100-81 3PH 1/2HP BASE MOUNT 208/230/460V SL575-50-23, SL575-50-43, SL575-50-83 3PH 1/2HP C-FACE/BM 575V SL575-50-53 3PH 1HP BASE MOUNT 208/230/460V SL575-100-23, SL575-100-43, SL575-100-83 3PH 1HP BASE MOUNT 575V SL575-100-53 115V ALL 115-1PH 230V ALL 230 1PH & 3PH, 460-3PH 575V 575V 3PH ON/OFF SWITCH 1PH ALL 115-1PH ON/OFF SWITCH 3PH ALL 3PH ON/OFF SWITCH 1PH 208/230 1PH 6 AMP SL575-50-21, SL575-50-81 8 AMP SL575-75-21, SL575-75-81, SL575-100-21, SL575-100-81 10 AMP SL575-50-11 1. 8 TO 2. 6 AMP SL575-100-53 31 SOLENOID SWITCH OVERLOAD WARRANTY POLICY AND SERVICE LIFTMASTER® TWO YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the first retail purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of two years from the date of purchase. [. . . ]