User manual LIFT-MASTER SL500

[. . . ] Installation and Maintenance Manual Slide Gate Operator Model SL500-11 Doc 01-20220 Rev D 2 Contents Contents General Information ____________________________________________ 4 Supplied Parts ___________________________________________________________ 4 Cycle Rate ______________________________________________________________ 4 Specifications ___________________________________________________________ 5 Dimensional Outline ______________________________________________________ 5 Safety Information ______________________________________________ 6 Safety Instructions________________________________________________________ 6 Safety Precautions for Open-Roller Gates and Ornamental "Grill Type" Gates ________ 8 Preparing the Installation _______________________________________ 10 Pre-installation Check List ________________________________________________ 10 Wiring Specifications ____________________________________________________ 10 Operator Features _______________________________________________________ 11 Programmable Features___________________________________________________ 14 Led Descriptions ________________________________________________________ 15 Installation ___________________________________________________ 16 Step 1: Step 2: Step 3: Step 4: Step 5: Step 6: Step 7: Step 8: Step 9: Mounting Legs __________________________________________________ 16 Pedestal Post (Optional) ___________________________________________ 17 Mounting ______________________________________________________ 18 Gate Brackets ___________________________________________________ 18 Drive Chain_____________________________________________________ 19 Chain Guards ___________________________________________________ 19 Battery Install ___________________________________________________ 20 Electrical Power Connections_______________________________________ 21 Programming ___________________________________________________ 22 Step 10: Limit Switch Adjustments _________________________________________ 27 Step 11: Preliminary System Check-Out _____________________________________ 28 Step 12: Accessory Installation_____________________________________________ 28 Required Maintenance__________________________________________ 30 Doc 01-20220 Rev D Contents 3 Troubleshooting _______________________________________________ 31 1. Power ______________________________________________________________ 31 2. Accessories__________________________________________________________ 32 3. Programs/Features ____________________________________________________ 32 4. [. . . ] RUN OBSTRUCTION RIGHT HAND INDICATOR L. E. D. s (Light Emitting Diode) CLOSING OPENING POWER FUNCTION & OPTION DISPLAY PANELS 01-20220f17 FUNCTION & OPTION PROGRAMMING BUTTONS Figure 15 Doc 01-20220 Rev D Installation 23 PROGRAM 1 ­ RIGHT HAND/LEFT HAND OPERATION Program 1 determines whether the operator is "right handed" or "left handed". To determine which type your gate controller needs to be set to, observe the installation from the operator side of the gate. 0 = NOT SELECTED ­ OPERATOR WILL NOT FUNCTION IN THIS MODE 1 = RIGHT HANDED ­ OPERATOR WILL MOVE GATE FROM LEFT TO RIGHT TO OPEN 2 = LEFT HANDED ­ OPERATOR WILL MOVE GATE FROM RIGHT TO LEFT TO OPEN If the operator is on the right side of the opening, the operator is "right handed". If the operator is on the left side of the opening, it is "left handed". 1 Press the FUNCTION select button to set the function to "1". Option "0" is the factory setting and does not allow gate movement. 2 Pressing the "OPTION" button will change the option between "1" and "2". When the correct option for your application is indicated, press the "FUNCTION" select button to save this selected option and to step to the next program. The option display will show a "0", "1" or "2". This option must be changed to either a "1" for right hand or "2" for left hand. PROGRAM 2 ­ MASTER/SLAVE OPERATION Program 2 selects whether the installation is a single operator or dual operators with common controls. 0 = SINGLE GATE OPERATOR INSTALLATION 1 = MASTER GATE OPERATOR 2 = SLAVE GATE OPERATOR 1 If the "FUNCTION" display shows "2", proceed on as follows. The "OPTION" display will indicate a "0", "1" or "2". The "0" option is the factory setting and is for single operator gates. Press the "OPTION" select button to change the option between "0", "1" or "2", where option "1" is for master operation. If it does not show "2" then press the "FUNCTION" select button to set the display to "2". The "0" option can be changed to "1" or "2" for dual gate operators. 2 3 Doc 01-20220 Rev D 24 Installation IMPORTANT: Once all programming is completed for the master operator, you must then program all features for the slave operator. All nine (9) programs should be the same except for ­ Program 1 (R. H. /L. H. ). In most cases one unit will be right handed and the other will be left hand. NOTE ­ MASTER/SLAVE OPERATION: The two operators must have the 3 interconnection wires in place between the two operators for the master/slave system to work. Reference the wiring diagram supplied with units. PROGRAM 3 ­ GATE OBSTRUCTION SENSITIVITY SELECT Program 3 selects the force required to make the internal speed sensor react. 0 = MINIMUM FORCE SETTING 1 = MODERATE FORCE SETTNG 2 = MEDIUM FORCE SETTING 3 = MAXIMUM FORCE SETTING 1 If the "FUNCTION" display shows "3", proceed on as follows. The "OPTION" display indicates a "0", "1", "2" or "3". [. . . ] Make sure that the wire itself, not the insulation of the wire is being clamped down on. Also check for a loose wire connection. General Reference Information THE GATE Double check the gate and its related hardware. If it does not, this can and will affect the unit's internal obstruction sensor. WIRING DIAGRAM Always reference the wiring diagram for this operator. Note that some accessory items may have their own wiring diagram. Doc 01-20220 Rev D Troubleshooting 35 COMPONENT DESCRIPTIONS A. [. . . ]