User manual LIFT-MASTER SL1000

[. . . ] Doc 6001204 (01-20260) Rev C INSTALLATION AND OPERATION INSTRUCTIONS FOR THE MODEL SL 1000-B1 SLIDE GATE OPERATOR (-68 BOARD) TABLE OF CONTENTS SAFETY SUMMARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 BASIC INSTALLATION HINTS AND RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PART 1 SITE PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LOCATION AND LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] See Appendix A for details on how each control input affects the gate operator. Connect the Master/Slave interconnect cable (see Part 3). Rev C Doc 6001204 (01-20260) Page 16 of 40 NOTES 1. Disconnecting the STOP terminal from the COMMON terminal stops the gate and prevents all commands from having any effect. Inside and Outside Interrupt Loops: · · · For maximum safety, Inside and Outside Interrupt loops require separate loop detectors. If only one loop detector is used, the Outside loop must also be connected to the Inside loop detector. In Bi-Parting and Bi-Parting Latch Master/Slave systems, to enhance system safety, Interrupt loops, Shadow loops and Interrupt Bar switches may be connected to both gates. If this is done, when connecting the two control boards, do not interchange input and common terminals. If terminals are interchanged, inputs will not be detected and controller boards may be damaged. Verify that switch S2 (the Gate Open Direction switch) is set to the correct position. Turn on the unit power switch (on master/slave systems, turn on slave and then master). Verify that Manual Open fully opens the gate and that the open limit switch stops the gate. Verify that Manual Close fully closes the gate and that the close limit switch stops the gate. Note: If the gate stops due to a Reverse Fault, readjust the gate sensitivity pot. Left/Right Reverse sensitivity: Apply a bump to the opening and closing gate and verify that the gate stops or reverses. Inrush (Gate response time) : Apply a bump to the gate as it initiates opening and closing and verify that the gate responds to the bump within a second. Rev C Doc 6001204 (01-20260) Page 17 of 40 5. If you want the gate to resume operation automatically up to 2 times, 30 seconds after a Fault, set RETRY on switch S1 to ON. If you do not want the gate to resume automatically after a Fault, set RETRY on switch S1 to OFF. Give the opening gate a quick bump to generate a fault and verify retry operation. Activate the CYCLE input (entry system), RADIO input (radio transmitter), and EXIT Loop input (driving over the exit loop) and verify that they fully open the gate. Activate the FIRE input (fire department switch) and verify that the gate fully opens and then closes immediately. If you want the CYCLE input (Entry system) or RADIO input (Transmitter) to both open and close the gate, on switch S1 set TIMER to OFF and ATG to OFF. Activate the CYCLE command, wait until the gate is fully open, then activate the CYCLE command again. [. . . ] Limit switch: A switch which its closure indicates the gate has reached its open or close limit, causing the gate to stop. Limit cam: An object which its excursion corresponds to the gate traveling distance and closes the limit switch at the open or close limit of the gate. Loop sensor: A wire embedded in the ground for magnetically sensing large metallic objects (cars). Interrupt or Reverse or Reopen Loop: activation reverses or stops the gate. [. . . ]