User manual LIFT-MASTER LOGIC 4

[. . . ] NOTE: When the power up process is over, the MAS LED will blink a code indicating the version of firmware. If the selector dial is in the DIAG, OPTN, or PROG position, the MAS will not provide this code. 2 LOGIC BOARD PUSH BUTTONS (OPEN, CLOSE, STOP) Open, Close and Stop buttons are mounted directly on the logic board. Thus, making it easy to program as well as have door control at the electrical box. [. . . ] Repeat to add additional remote control(s). MID SLS CLS MRT MID TTC TIM ENA TIM ENA RADIO 1 2 3 ATTENTION RADIO 1 2 3 Press and release the RADIO button to complete the programming. The programming mode is exited if no activity is performed within 30 seconds. AVE ASE ASE MOTOR DIRECTION 3-BUTTON REMOTE CONTROL TO OPERATE AS A WIRELESS 3-BUTTON CONTROL STATION NOTE: The feature will use 3 of the 23 memory channels in the operator. MOTOR DIRECTION AV T E2 TS FSTS E2 T TS FSTS 1 MID SLS CLS MRT MID TTC TIM ENA RADIO 1 2 3 Press and release the RADIO button on the logic board (the Radio LED will light). 2 LMEP: TTC TIMER ENABLE EDGE: OPEN 3 CLOSE STOP FSTS DIAG T E2 TS FSTS OPTN COMMON Press and release the desired button on the logic board (OPEN, CLOSE or STOP). The Radio LED will flash and then stay on solid. 3 HASE Press and hold the desired button of the remote control until Radio LED flashes rapidly, then release. Repeat steps 1 through 3 to program additional buttons. TO ERASE ALL REMOTE CONTROLS MOTOR DIRECTION ADVERTENCIA AD PRECAUCIÓN 1 A HASE MID SLS CLS MRT MID TTC TIM ENA RADIO 1 2 3 T E2 TS FSTS Press and hold the RADIO button on the logic board until the RADIO LED flashes rapidly (approximately 5 seconds). All remote controls will be erased. MOTOR DIRECTION 4 BASIC PROGRAMMING WARNING To prevent possible SEVERE INJURY or DEATH: · Install a LiftMaster Monitored Entrapment Protection (LMEP) device. · NEVER permit children to operate or play with door control push buttons or remote controls. · Activate ONLY when it can be seen is properly CAUTION door there are no obstructions toclearly, travel. adjusted and door · ALWAYS keep door in sight until completely closed. NEVER permit anyone to cross path of closing door. W TIMER-TO-CLOSE Feature: Timer automatically closes door after preset time. Benefit: The door will automatically close after preset amount of time. Great for apartment buildings, fire stations and other applications where the end user wants the door to close automatically after a specified amount of time. Requirements: Must have at least one LiftMaster Monitored Entrapment Protection (LMEP) device installed (refer to page 20). Press and release the OPEN button for every second the operator should wait before attempting to close the door. Press and release the CLOSE button for every 15 seconds the operator should wait before closing the door. The OPEN LED will flash once for every second programmed and the CLOSE LED will flash once for every 15 seconds programmed. Turn selector dial to PROGRAM, press and release the TIMER button, press and release the STOP button to clear the timer, press and release the CLOSE button four times for 60 seconds and press and release the OPEN button 10 times for 10 seconds. Emergency disconnect will open. 1 2 1 AVERTISSEMENT AVE TO RECONNECT DOOR ARM TO TROLLEY Lift free end of door arm to trolley. Emergency disconnect will close. ATTENTION AV 2 NOT ICE EMERGENCY DISCONNECT SYSTEM MODEL APT TO DISCONNECT DOOR FROM OPERATOR The door should be in the fully closed position if possible. Pull down on the emergency release handle and raise or lower the door manually. ADVERTENCIA AD 1 2 PRECAUCIÓN A TO RECONNECT DOOR ARM TO TROLLEY The trolley will reconnect on the next UP or DOWN operation, either manually or by using the door control or remote. 1 NOT ICE 6 MANUAL RELEASE EMERGENCY DISCONNECT SYSTEM MODEL H, GH, J, AND HJ This operator has provisions for manually operating the door in case of emergency or power failure. An electrical interlock will disable the electrical controls when the hoist is used. To operate the hoist: WARNING CAUTION To prevent possible SERIOUS INJURY from a moving chain: · DISCONNECT electric power to the operator BEFORE manually operating your door. · If possible, use emergency disconnect ONLY when door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly. [. . . ] Cast iron bracket to mount J, H, DH, DJ, and GH side mount operators on end bracket of a rolling door or grill. Same as 08-9098, but with adapter plate to hold mounting bolt holes in place for ease of use. OPEN CLOSE TLSCARD Timer Light Status Card: The TLS option card provides special functionality to activate and flash auxiliary devices such as lights, bells, and horns/strobes at various door positions, and to provide special timer functions. 08-9098 AUXCARD Auxiliary Contact Card: The Auxiliary Contact option card has both Normally-Open and Normally-Closed contacts that actuate when the door is idle, opening, or closing. 08-9098EZ MOUNTING CHANNELS 65ME123C 1A4324 Heavy gauge steel bracket for vertical or horizontal mount on either front or top of coil on a rolling door. Same as 1A4324, but with adapter plate to hold mounting bolt holes in place for ease of use. OPEN CLOSE U-Shaped Mounting Channel: For 65ME1234 edge when installed on sectional doors. 65ME123C1 OPEN T-Shaped Mounting Channel: For 65ME1234 edge when installed on rolling doors. Fits between L-shaped angles used to construct a bottom bar on rolling doors. [. . . ]