User manual LIFT-MASTER H

[. . . ] Logic 3 OWNER'S MANUAL J H HJ INDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR This Operator Features the Enhanced IN T ENA N C E M A E R T SYS T The Maintenance Alert SystemTM allows the installer to set an internal Maintenance Cycle Counter. The Logic 3 operator incorporates a self-diagnostic feature built into the (MAS) Maintenance Alert System LED. An LED on the 3-button station will signal when the set number of cycles/months is reached or when the operator requires immediate service. Radio Receiver Built on Board 2 YEAR WARRANTY 315MHz Serial # Box Installation Date NOT FOR RESIDENTIAL USE E PAT E N T P E N D I N G M A L TABLE OF CONTENTS SPECIFICATIONS Carton Inventory . . 5 AUTOMATICALLY LEARNED PROGRAMMING Auxiliary Reversal System/RPM Sensor. [. . . ] SINGLE BUTTON CONTROL (SBC) REMOTE This function programs a remote as a wireless single button control. In C2 mode, operation is OPEN / STOP/ Constant pressure to CLOSE / STOP on release. In T and TS modes, operation is OPEN / STOP / CLOSE / REVERSE / STOP and Timer to Close start/refresh. In FSTS mode, operation is OPEN with Timer to Close start/refresh only bypassing all up mid stops. Momentary and constant pressure commands are processed in this function. OPERATION CAUTION NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ø14LGØ65 P4 E1 R29 C11 MODE B2 C2 D1 E2 T, TS FSTS OPEN STOP CLOSE Reverse Constant Pressure Timer To Close D3Ø2 X1 U1 K3 RADIO D16 P7 OLS D25 MID D24 1. Press and release the RADIO button on the logic board (LED will light). Press and release the SBC externally wired button or TIMER on the logic board (LED flashes rapidly and then remains on solid). Press and release the RADIO button on the logic board (LED flashes rapidly and then turns off). The programming mode is exited if no activity is performed within 30 seconds. ERASING REMOTES Press and hold the RADIO button on the logic board until the RADIO LED flashes rapidly (approximately 5 seconds). All remotes will be erased. SLS D26 CLS MRT MID D27 TIM RADIO 1 D36 2 RELAY C77 D35 C73 RELAY E2 D1 L1 LiftM ast er C2 C71 L5 B2 FAILSAFE P6 18 MOTOR REV C54 C78 ® PROGRAMMING Your 315MHz Security®or dip switch remote control can be programmed to operate as a 3-button wireless control station: the large button will open the door, the middle button will close the door, and the third button will stop the door's movement. To enter programming press the RADIO button on the logic board (the RADIO LED will light). To program the OPEN button to a remote control press the OPEN button on the logic board. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver. ) 3. To program the CLOSE button to a remote control press the CLOSE button on the logic board. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver. ) 4. To program the STOP button to a remote control press the STOP button on the logic board. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver. ) 5. [. . . ] 3. 0) For replacement of electrical box, motor or brake components be sure to match model number of your unit to kit number below to ensure proper voltage requirements. SERVICE KITS ITEM PART # DESCRIPTION K1 K72-14130-1 Limit shaft kit Complete with: Limit shaft, limit nuts, limit bearings, limit sprocket, interrupter cup, shim washers, compression ring, roll pin, and e-rings. K2 K72-12515-1 Limit switch kit Complete with: Limit nut retainer, switch plates, backup plate, depress plates, limit switches, standoffs, screws, and locknuts. *To order a complete electrical box kit, add a K- prefix to the model number of your operator. [. . . ]