User manual LG APNZ286R20

[. . . ] The seriousness is classified by the following indications. ENGLISH WARNING CAUTION This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage. n Meanings of symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. WARNING n Installation Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit. · There is risk of fire or electric shock. For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center. · Do not disassemble or repair the product. [. . . ] Power ON/OFF Button · Operation will start when this button is pressed, and stop when the button is pressed again. Electric Heater ON/OFF Button(Heat Pump & Electric Heater Product Only) 9 A/CL 10 11 6 12 13 14 7 8 (Cooling Model) Wireless Remote Control Puts all functions at your fingertips Handling the remote control · Aim at the signal receptor on the floor standing type air conditioner when operating. · The remote control signal can be received at a distance of up to about 7meters. · Be sure that there are no obstructions between the remote control and the signal receptor. · Do not place the remote control in a location exposed to direct sunlight, or next to a heating unit, or other heat source. Owner's Manual 9 Operating Instructions Remote Control Preparation 1. How to mount onto a wall Use the screws to secure the holder to the wall or attach the holder side of indoor unit. · Please keep it on the right side of indoor unit. When opening When closing 2. To insert the remote control to the holder. Insert Pull How to insert batteries 1. · Do not use rechargeable batteries such batteries as different from standard dry cells in shape, dimensions, and performance. · Change the batteries with a new one if the remote control does not work properly after using for an extended length of time. 10 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Cooling Operation Mode 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Select Cooling Operation. Press the Cooling Operation Button on the remote controller (or Touch the Cooling Operation key on the touch panel) SET A/CL TEMP. TURBO-Z ON/OFF PLASMA 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. SET To raise the temperature To lower the temperature TURBO-Z TEMP. ON/OFF PLASMA 4 When you finish the temperature setting. After 4 seconds ROOM TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA TEMP. ON/OFF PLASMA 5 Set the Fan Speed. Low TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA Mid High q Each time the Fan Speed Button is pressed (or fan speed key is touched), the Fan Speed mode is shifted in the arrow direction. Owner's Manual 11 Operating Instructions Soft Dry Operation 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Select Soft Dry Operation Press the Soft Dry Operation Button on the remote controller (or Touch the Soft Dry Operation key on the touch panel) SET A/CL TEMP. TURBO-Z ON/OFF PLASMA 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature SET TEMP. TURBO-Z ON/OFF PLASMA During softy Dry Operation · The indoor fan speed is automatically set to low and can be set fan speed. Low TURBO-Z ROOM TURBO-Z TEMP. ON/OFF PLASMA Mid High 12 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Turbo-Z cooling Operation 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Press the Turbo-Z Cooling button to operate the speed cooling mode and the unit will operate in super high fan speed on cooling mode. To cancel the Turbo-Z Cooling mode, press the Turbo-Z Cooling button or the Auto Swing Direction Control Button (Up & Down, Left & Right) and the unit will operate in Med Fan speed mode on cooling mode. TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA 3 To cancel the Turbo-Z Cooling mode, press the Turbo-Z Cooling button again or the Auto Swing Direction Control Button (Up & Down, Left & Right) and the unit will operate in Med. Fan speed on cooling mode. TURBO-Z A/CL NOTICE o During the Turbo-Z Cooling function at any moment, the A/C starts to blow the cool air at extremely high speed setting the room temp. In heat pump mode or neuro fuzzy mode however, the Turbo-Z Cooling function is not available. o In order to return to the normal cooling mode from the Turbo-Z Cooling mode, you just press either the operation mode selection button, airflow volume selection or temp. setting button or the Turbo-Z Cooling button again. Owner's Manual 13 Operating Instructions Heating Operation Mode(Heat Pump & Heater, Heat Pump Model) 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Select Heating Operation Press the Heating Operation Button on the remote controller (or Touch the Heating Operation key on the touch panel. ) SET A/CL TEMP. TURBO-Z ON/OFF PLASMA 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature SET TEMP. TURBO-Z ON/OFF PLASMA 4 Set the Fan Speed. TURBO-Z ROOM TURBO-Z TEMP. ON/OFF PLASMA Low High q Each time the Button is pressed, the Fan Speed mode is shifted. 14 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Electric Heater Operation Mode(Heater, Heat Pump Model) 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA controller 2 Press the Heating & E/Heater Operation Button on the remotepanel) (or Touch the heating & E/Heater Operation key on the touch Select Heating + E/Heater Operation. SET TEMP. A/CL A/CL ON/OFF PLASMA TURBO-Z 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature SET TEMP. TURBO-Z ON/OFF PLASMA 4 Set the Fan Speed. TURBO-Z Low SET TEMP. TURBO-Z ON/OFF PLASMA High * Each time the Button is pressed, the Fan Speed mode is shifted. Owner's Manual 15 Operating Instructions Auto Operation Mode(Cooling Model Only) 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Select Auto Operation Press the Auto Operation Button on the remote controller (or Touch the Auto Operation key on the touch panel) SET A/CL TEMP. TURBO-Z ON/OFF PLASMA 3 Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level. SET TEMP. TURBO-Z ON/OFF PLASMA Cold Cool Proper Warm Hot (This indication will be shifted to the initial Auto Mode Display state after 4 seconds. ) To raise the temperature (When you feel too cool or cold) To lower the temperature (When you feel too warm or hot) During Auto Operation · It is impossible to switch the indoor fan speed because of being already set to the best conditioner by fuzzy rule. 16 Floor Standing-Type Air Conditioner Operating Instructions ENGLISH Energy Saving Mode(Cooling & Soft Dry Operation Only) 1 Press the on/off button. (or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TURBO-Z TEMP. ON/OFF PLASMA 2 Press the Energy Operation Button on the remote controller (or Touch the Energy Saving Operation key on the touch panel) Select Energy Saving Operation TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA 3 To cancel the Energy Saving mode. Press(Touch) the Energy Saving Button(Key) Again and the nit will operate on Cooling/Auto/Soft Dry mode. TURBO-Z SET TEMP. TURBO-Z ON/OFF PLASMA Auto restart In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate procedures automatically to the previous operating conditions. Owner's Manual 17 Operating Instructions Airflow Direction Procedure 1 Press the on/off button (or touch the anyplace of touch panel and touch the on/off key) 2 TURBO-Z Press the Auto Swing Button and then louvers will swing Up and down. [. . . ] What To Do · Make sure the air conditioner plug is pushed completely into the outlet. · Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. When power is restored, wait 3 minutes to restart the air conditioner to prevent tripping of the compressor overload. · Make sure there are no curtains, blinds, or furniture blocking the front of the air conditioner. [. . . ]