User manual LEXMARK Z42

[. . . ] Lexmark Z42 Color Jetprinter TM User's Guide for Windows 95 and Windows 98 Edition: January 2000 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. , PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. [. . . ] For help accessing the printer driver Help, see page 6. Preserving print cartridges To ensure the longest life from your print cartridge and optimum performance from your printer: · Keep a new print cartridge in its packaging until you are ready to install it. · Do not remove a print cartridge from the printer except to replace, clean, or store it in an air-tight container. The print cartridge does not print correctly if removed from the printer and left exposed for an extended period of time. · If a print cartridge runs out of ink, leave the empty cartridge in the printer until you are ready to replace it. Printing with only one of the print cartridges in the printer may cause printer problems. Lexmark's printer warranty does not cover repair of failures or damage caused by a refilled cartridge. Refilling cartridges can affect print quality and cause damage to the printer. For best results, use Lexmark supplies. 26 · Chapter 3 · · · · 4 Printer prints slowly or doesn't print (see page 28) Paper misfeeds or jams (see page 31) Document prints with mistakes or poor quality (see page 32) Problems with transparencies, photos, or envelopes (see page 35) Error messages and flashing lights (see page 36) Troubleshooting From the list of printing problems in the left margin, select a category that describes your printing problem, and then read the category for the solution. When your printer has a problem, first make sure that: · The power supply is plugged into the printer and a properly grounded electrical outlet. · The printer cable is securely attached to your computer and printer. · If you are using a parallel cable, make sure it is an IEEE 1284-compliant parallel cable that supports bidirectional printing. · If you are using Windows 98 or Windows 2000, your printer port is set to an LPTn port for a parallel cable, or to a USB port for a USB cable. To check your printer port and change it if necessary, follow the appropriate set of instructions: Windows 98 1 From the File menu of your software application, select Print (or Printer) Setup. 2 Check your printer port in the Where area. Troubleshooting · · 27 · · · Troubleshooting 3 If you need to change your printer port to a USB port, uninstall and then reinstall the printer software. Follow the instructions on page 38, making sure to click Next on any screens. If you need to change your printer port to an LTPn port, uninstall and then reinstall the printer software. Follow the instructions on page 38, making sure to click Cancel on any screens. Windows 2000 1 From the Start menu, select Settings, and then select Printers. 2 From the Printers folder, right-click the printer icon for your printer. 4 From the Ports tab, select USB or LPTn to change your printer port if necessary. 5 Click OK. Printer prints slowly or doesn't print Your printer and your computer may not be able to communicate properly. The following events also indicate two-way communications problems: · A message displays on your computer screen indicating your printer cannot establish bidirectional communications with your computer. [. . . ] Such developer is an intended beneficiary of this limitation. Electronic emission notices Federal Communications Commission (FCC) Compliance Information Statement The Lexmark Z42 Color Jetprinter has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The FCC Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]