User manual LEXMARK PLATINUM PRO900

[. . . ] Use only the power supply and power cord provided with this product or the manufacturer's authorized replacements. Use only the telecommunications (RJ-11) cord provided with this product or a 26 AWG or larger replacement when connecting this product to the public switched telephone network. CAUTION--SHOCK HAZARD: Make sure that all external connections (such as Ethernet and telephone system connections) are properly installed in their marked plug-in ports. This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. [. . . ] The printer supports WPS and can be configured for wireless access using WPS. In order to use WPS to configure the printer, the wireless router must also support WPS. If you want to use WPS to set up your printer, then insert the CD and follow the instructions on the computer screen. Notes: · To use WPS to configure the printer wirelessly, all of the devices on your wireless network must support WPS. If any device on your network does not support WPS, then you must type the SSID and security information when prompted. · If you are using the PIN method to add your printer using WPS, make sure you type all eight digits when you are asked to enter your PIN. Switching between USB, Ethernet, and wireless connections (Windows only) You can change the way you access your printer, depending on your needs. The following procedures assume that you have configured your printer for one type of connection and that the printer drivers are installed on the computer. See related topics on troubleshooting specific connection types if you encounter difficulties during configuration. Note: The printer supports one active local connection (USB) and one active network connection (Ethernet or wireless) at a time. It is not possible to use both Ethernet and wireless at the same time. Using the printer wirelessly Select the connection type that describes how you currently access your printer: If the printer is currently set up locally (using USB connection) 1 Click or Start. 2 Click All Programs or Programs, and then select the printer program folder from the list. 6 Follow the instructions on the computer screen to set up the printer wirelessly. Note: There is no need to remove the USB cable connecting the printer to the computer during wireless configuration. Networking 110 If the printer is currently set up for Ethernet 1 Unplug the Ethernet cable from the printer. 2 Place the printer close to the computer you want to use to configure the printer for wireless access. Note: You will need to connect the printer to the computer with a USB cable. Make sure the printer is close enough to the computer for your USB cable to reach both. 3 Click or Start. 4 Click All Programs or Programs, and then select the printer program folder from the list. 8 Follow the instructions on the computer screen to set up the printer wirelessly. Using the printer locally (USB) Select the connection type that describes how you currently access your printer: If the printer is currently set up for Ethernet 1 Attach a USB cable to the computer and to the printer. 2 Wait for a moment for Windows to locate the driver and finish setting up the printer. 3 Select the USB printer (see "Selecting the printer" on page 112). If the printer is currently set up for wireless 1 Attach a USB cable to the computer and to the printer. 2 Wait a moment for Windows to locate the driver and finish setting up the printer. 3 Select the USB printer (see "Selecting the printer" on page 112). Note: You can continue to use the printer through Ethernet or wireless connection. Using the printer over an Ethernet network Select the connection type that describes how you currently access your printer: If the printer is currently set up for wireless 1 Plug an Ethernet cable into the printer and into an available port on a switch or wall jack. 2 Wait for a minute for the Ethernet network interface to become active and acquire an IP address from the network. 3 Select the Network printer (see "Selecting the printer" on page 112). Note: The wireless interface of the printer is disabled while it is connected to an Ethernet network. If the printer is currently set up locally (using USB connection) 1 Plug an Ethernet cable into the printer and into an available port on a switch or wall jack. 2 Insert the software and installation CD into the computer you want to use to configure the printer. Networking 111 3 Follow the instructions on the computer screen for configuring a printer on an Ethernet network. 4 Select the Network printer (see "Selecting the printer" on page 112). Note: You will need a USB cable to complete the configuration. Selecting the printer 1 Click or Start. 2 In the Start Search or Run box, type control printers. [. . . ] Compliance is indicated by the CE marking. Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only. The manufacturer of this product is: Lexmark International, Inc. , 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft. , 8 Lechner Ödön fasor, Millennium Notices 189 Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative. Cesky Dansk Deutsch Spolecnost Lexmark International, Inc. tímto prohlasuje, ze výrobek tento výrobek je ve shod se základními pozadavky a dalsími píslusnými ustanoveními smrnice 1999/5/ES. [. . . ]