User manual LEXMARK IBM TYPEWRITER 6747

[. . . ] You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions. CAUTION--POTENTIAL INJURY: There is a danger of explosion if a lithium battery is incorrectly replaced. Replace it only with the same or an equivalent type of lithium battery. Discard used batteries according to the manufacturer's instructions and local regulations. [. . . ] Settings range from 1­120 minutes. Confidential Print menu Menu item Max Invalid PIN Off 2­10 Description Limits the number of times an invalid PIN can be entered Notes: · Off is the factory default setting. · Once a limit is reached, the jobs for that user name and PIN are deleted. Limits the amount of time a confidential job stays in the printer before it is deleted Note: Off is the factory default setting. Job Expiration Off 1 hour 4 hours 24 hours 1 week Understanding printer menus 95 Security Audit Log menu Menu item Export Log Description Enables an authorized user to export the security log Notes: · To export the log from the printer control panel, a flash drive must be attached to the printer. · From the Embedded Web Server, the log can be downloaded to a computer. Delete Log Delete now Do not delete Configure Log Enable Audit Yes No Enable Remote Syslog No Yes Remote Syslog Facility 0­23 Severity of events to log 0­7 Specifies whether audit reports of print jobs are deleted Note: Delete now is the factory default setting. Specifies whether and how the audit logs of print jobs are created: · Enable Audit determines if the printer records events in the secure audit log and in the remote syslog. · Enable Remote Syslog determines if the printer sends logged events to a remote server. · Remote Syslog Facility determines the facility value that the printer uses when sending events to the remote syslog server. · "Severity of events to log" specifies how critical a logged event is. With this log activated, the printer logs each event with a severity value equal to or less than the setting value. 0 is Emergency 1 is Alert 2 is Critical 3 is Error 4 is Warning 5 is Notice 6 is Informational 7 is Debug Notes: · Yes is the factory default setting for Enable Audit. If Enable Audit is set to No, then no records are sent to the remote syslog even if Enable Remote Syslog is set to Yes. · 4 Security is the factory default setting for Remote Syslog Facility. · 4 is the factory default setting for Severity of events to log. Understanding printer menus 96 Set Date/Time menu Menu item View Date/Time Description Lets you view the current date and time settings for the printer. The format for the date and time is: YYYYMMDD HH:MM: YYYY is the fourdigit year MM is a twodigit month DD is a twodigit date HH is a twodigit hour MM is a twodigit minute Lets you enter the date and time Note: Date/Time is set in YYYY-MM-DD HH:MM format. Time Zone <list of time zones> Observe DST On Off Enable NTP On Off Lets you select the time zone Note: GMT is the factory default setting. Sets the printer to use the applicable Daylight Saving Time (DST) start and end times associated with the printer Time Zone setting. Enables Network Time Protocol, which synchronizes the clocks of devices on a network Note: On is the factory default setting. Set Date/Time Understanding printer menus 97 Settings menu General Settings menu Menu item Display Language English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese Eco-Mode Off Energy Energy/Paper Paper Description Sets the language of the text appearing on the display Minimizes the use of energy, paper, or specialty media Notes: · Off is the factory default setting. Custom Home Message Off IP Address Hostname Contact Name Location Zero Configuration Name Custom Text 1 Sets a preconfigured or customized message to appear on the display beside Ready Notes: · Off is the factory default setting. · Contact Name, Location, Zero Configuration Name, and Custom Text 1 are messages that can be customized by a system support person. Setup menu Menu item Printer Language PCL Emulation PS Emulation Description Sets the default printer language Notes: · PCL emulation uses a PCL interpreter for processing print jobs. PostScript emulation uses a PS interpreter for processing print jobs. · PCL is the factory default printer language. · Setting a printer language as the default does not prevent a software program from sending print jobs that use another printer language. Understanding printer menus 101 Menu item Print Area Normal Whole Page Description Sets the logical and physical printable area Notes: · This menu does not appear if Edge to Edge is enabled in the printer Setup menu. · Normal is the factory default setting. When attempting to print data in the nonprintable area defined by the Normal setting, the printer clips the image at the boundary. · The Whole Page setting allows the image to be moved into the nonprintable area defined by the Normal setting, but the printer will clip the image at the Normal setting boundary. · The Whole Page setting affects only pages printed using a PCL 5e interpreter. This setting has no effect on pages printed using the PCL XL or PostScript interpreter. Download Target RAM Flash Sets the storage location for downloads Notes: · RAM is the factory default setting. · Storing downloads in flash memory places them in permanent storage. Downloads remain in flash memory even when the printer is turned off. · Storing downloads in RAM is temporary. · This menu appears only if optional flash memory is installed. Resource Save On Off Specifies how the printer handles temporary downloads, such as fonts and macros stored in RAM, when the printer receives a job that requires more memory than is available Notes: · Off is the factory default setting. Off sets the printer to retain the downloads only until memory is needed. [. . . ] Prior to the transfer, the end-user receiving the transferred Software Program must agree to all these License Agreement terms. Upon transfer of the Software Program, your license is automatically terminated. You may not rent, sublicense, or assign the Software Program except to the extent provided in this License Agreement, and any attempt to do so shall be void. To Use a Software Program identified as an upgrade, you must first be licensed to the original Software Program identified by Lexmark as eligible for the upgrade. [. . . ]