User manual LEXMARK E352DN

[. . . ] E350d and E352dn User's Guide June 2006 www. lexmark. com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 Edition:June 2006 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. , PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] If the job you want to cancel is printing, and Busy appears on the display, press press . until Cancel a job appears, and then Canceling a job from a computer running Windows Canceling a job from the taskbar When you send a job to print, a small printer icon appears in the right corner of the taskbar. 1 2 3 Double-click the printer icon. Press the Delete key on the keyboard. Canceling a job from the desktop 1 2 3 4 5 6 Minimize all programs to reveal the desktop. Press the Delete key on the keyboard. Canceling a print job 25 Printing Canceling a job from a Macintosh computer Canceling a job from a Macintosh computer running Mac OS 9. x When you send a job to print, the printer icon for your selected printer appears on the desktop. 1 2 3 Double-click the printer icon on your desktop. Click the trash can icon. Canceling a job from a Macintosh computer running Mac OS X 1 2 3 4 Open Applications à Utilities, and then double-click Print Center or Printer Setup. Press Delete. Printing the menu settings page You can print a menu settings page to review the default printer settings and to verify printer options are installed correctly. 1 2 3 4 Make sure the printer is on and Ready appears. From the control panel, press Press Press until Utilities Menu appears, and then press . until Print Menus appears. , Printing Menus Settings appears. The indicator light flashes, and the printer prints the pages. The printer returns to the Ready state. Printing the menu settings page 26 Printing Printing a network setup pag e If the printer is attached to a network, print a network setup page on the printer to verify the network connection. This page also provides important information that helps in configuring for network printing. 1 2 3 4 5 6 7 Make sure the printer is on and Ready appears. until Network Menu appears, and then press . until Reports appears. until Setup Page appears, and then press again. Busy Network appears. Press to return to the Ready state. Check the first section on the network setup page, and confirm that Status is "Connected. " If Status is "Not Connected" the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and print another network setup page to verify that the printer is connected to the network. Printing a font sample list To print samples of the fonts currently available for your printer: 1 2 3 4 5 Make sure the printer is on and Ready appears. From the control panel, press Press Press until Utilities Menu appears, and then press . until Print Fonts appears. until List appears. The indicator light flashes, and the printer prints the pages. Press to return to the Ready state. Printing a network setup page 27 4 Installing options Accessing the system board CAUTION: To install memory, you must access the printer system board. Turn the printer off, and unplug the power cord from the wall outlet before continuing. 1 Remove the 250-sheet paper tray. Installing options 28 Installing options 2 Press the button on the left side of the printer to release and lower the front door. 3 Open the rear exit door. Accessing the system board 29 Installing options 4 Press both buttons on the front right side of the machine to release the side access door. 5 6 7 Loosen the four screws on the cover, but do not remove them completely. Slide the cover to the left until the screws fit into the keyholes on the cover. Remove the cover and set it aside. Accessing the system board 30 Installing options Adding a memory card The system board has one connector for an optional memory card. CAUTION: If you are installing a memory card after setting up the printer, turn the printer off, and unplug the power cord from the wall outlet before continuing. Note: Memory options designed for other Lexmark printers may not work with your printer. 1 2 3 Access the system board (see Accessing the system board on page28 ). Touch something metal, such as the printer frame, before you touch a memory card. [. . . ] You should transfer proof of original purchase and this statement to that user. Limited warranty service The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided t hat the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location. [. . . ]