User manual LEXMARK C910

[. . . ] Lexmark C910 User's Reference October 2001 www. lexmark. com Table of contents Chapter 1: Printer overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Print speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Paper handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not store supplies in: · · · · · · · Temperatures greater than 43°C (110°F) An environment with extreme changes in humidity or temperature Direct sunlight Dusty places A car for a long period of time An environment where corrosive gases are present An environment with salty air 112 33 Resetting the maintenance counter After replacing the fuser or transfer belt, you must reset the maintenance counter. Otherwise, use the following steps to reset the fuser or transfer belt counter. Note: Although the fuser is shown, the same procedure is used to clear the transfer belt. 1 Press Menu until Supplies Menu appears on the second line of the display. SUPPLIES MENU 1 Menu 2 Select 3 Return 4 Go 5 Stop 6 2 Press Select to open the Supplies Menu. 3 Press Menu until Replace Supplies appears on the second line of the display. SUPPLIES MENU REPLACE SUPPLIES 1 Menu 2 Select 3 Return 4 Go 5 Stop 6 4 Press Select to open Replace Supplies. 113 5 Press Menu until Fuser appears on the second line of the display. REPLACE SUPPLIES Fuser 1 Menu 2 Select 3 Return 4 Go 5 Stop 6 6 Press Select to open the Fuser menu item. 7 Press Menu until =Replaced appears on the second line of the display. Fuser =Replaced 1 Menu 2 Select 3 Return 4 Go 5 Stop 6 8 Press Select to reset the fuser counter to zero. 9 Press Go. 114 34 Removing memory and network options Previously installed memory and interface options can easily be removed by using the procedures on the following pages. 1 Turn the printer off. 3 Disconnect the parallel or Ethernet cable from the printer. If you have any other devices connected to the printer, turn them off as well and unplug any cables going to the printer. Removing the system board access cover You must remove the system board access cover to install memory cards, a firmware card, a hard disk, or an option card. CAUTION: This printer weighs 69. 9 kg (154 Ib) and requires four people to lift. Anytime you move or lift the printer make sure you have enough people to help. Use the handholds located on the sides to lift the printer. 1 Move the printer or place it in an area that will be convenient for removing the cover and components. You need a number 2 Phillips screwdriver to remove the cover and system board. 2 Loosen the eight screws on the cover. Do not remove the screws completely. 115 3 Slide the cover up and away from the printer. WARNING: The system board access cover must be replaced before operating the printer. Screws Screws Locating memory and network options Use the following illustration to locate the connector for the card you want to remove. Memory and flash memory card connectors Option card connector Parallel connector Optional ImageQuickTM firmware card USB connector Optional hard disk Ethernet connector 116 Removing a memory card Complete the following steps if you need to remove a memory card. Otherwise, go to Installing the system board access cover. 1 Make sure the printer is turned off and the power cord is unplugged. 2 Follow the steps for Removing the system board access cover if it is still installed. WARNING: Memory cards are easily damaged by static electricity. Touch something metal such as the printer frame before you touch a memory card. 3 Push the latches at each end of the connector away from the card. The memory card moves out of the connector as the latches open. 4 Gently pull the card out. 5 Place the card into the original packaging. If you do not have the original packaging, wrap the card in paper and store it in a box. 6 Close both latches. 7 Repeat steps 3 through 6 to remove additional memory cards. 117 Removing an option card You need a number 2 Phillips screwdriver to remove an option card. 1 Make sure the printer is turned off and the power cord is unplugged. 2 Complete the steps for Removing the system board access cover if it is still installed. WARNING: Option cards are easily damaged by static electricity. Touch something metal such as the printer frame before you touch an option card. 3 Remove the screws securing the option card to the cover. 118 4 Gently pull the option card completely out. 5 Place the option card in its original packaging. If you do not have the original packaging, wrap the option card in paper and store it in a box. 6 If you are not installing another option card in the connector, cover the opening with a blank internal print server cover. If you do not have a blank cover, contact your service representative and request one. Removing a firmware card 1 Make sure the printer is turned off and the power cord is unplugged. 2 Complete the steps for Removing the system board access cover if it is still installed. WARNING: Firmware cards are easily damaged by static electricity. Touch something metal such as the printer frame before you touch a firmware card. If an option card has been installed, you need to remove the option card before removing the firmware card. 119 3 Holding the firmware card by its sides, gently pull the card completely out. Avoid touching the metal pins on the bottom of the card. 4 Place the firmware card in its original packaging. If you do not have the original packaging, wrap the firmware card in paper and store it in a box. 5 If you removed an option card to access the firmware card, reinstall the option card. Removing a hard disk 1 Make sure the printer is turned off and the power cord is unplugged. 2 Complete the steps for Removing the system board access cover if it is still installed. WARNING: Hard disks are easily damaged by static electricity. [. . . ] This product is designed, tested, and approved to meet strict global safety standards with the use of specific Lexmark components. Lexmark is not responsible for the use of other replacement parts. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. · Your product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions. Cautions and warnings CAUTION: A caution identifies something that might cause you harm. WARNING: A warning identifies something that might damage your printer hardware or software. 310 Electronic emission notices Federal Communications Commission (FCC) compliance information statement The Lexmark C910 has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ]