User manual LEXICON I-ONIX U22

[. . . ] Owner's Manual IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS THE APPARATUS SHALL NOT bE ExPOSED TO DRIPPING OR SPLASHING LIqUID AND NO ObjECT FILLED WITHI LIqUID, SUCH AS vASES, SHALL bE PLACED ON THE APPARATUS. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOvES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT. ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED bY THE MANUFACTURER. Safety InStructIOnS Notice For customers iF Your uNit is equipped With A poWer cord. WArNiNG: this AppLiANce shALL Be coNNected to A mAiNs socKet outLet With A protectiVe eArthiNG coNNectioN. [. . . ] OutPut LeveL LeDS These indicate signal level for each output by showing the remaining headroom before clipping. Their values are: Red Clipping Yellow ­3dB Green ­6dB Green ­9dB Green ­12dB Green ­18dB Green ­24dB Green ­30dB 3. MIc/LIne/InSt 1 GaIn KnOB Adjusts the input gain level for Mic/Line 1 or Instrument 1. 3 5. InStruMent LeD Lights when a 1/4" plug is inserted into the Instrument jack on the right side panel. 6. StereO ButtOn anD StereO LeD This button toggles between Stereo mode and Mono mode for the Mic/Line 1 input (or Instrument input) and Mic/Line 2 input. In Stereo mode (Stereo LED is on), the Instrument and Mic/Line 1 input signals are sent to the Left Main Out, while the Mic/Line 2 input signal is sent to the Right Main Out. In Mono mode (Stereo LED is off ), each pair of input signals is mixed together and sent to the Left and Right Main Outs as a mono signal. 48v LeD Lights when phantom power is active for the Mic/Line 1 and 2 input pair. Phantom power can be turned on for the combi-jack input pair via the 48V buttons on the back panel. Dynamic microphones do not require phantom power to operate, but are not harmed by it. If you are unsure about the phantom power requirements for your microphone, consult your microphone's documentation or contact the manufacturer. 8. MIc/LIne 2 GaIn KnOB Adjusts the input gain level for Mic/Line 2. 9. OutPut LeveL KnOB Controls the Left and Right Main output level. 10. MOnItOr MIx KnOB The I·ONIX U22 unit gives you the ability to hear your analog input signals directly and immediately while recording without having to adjust levels in software and before the delay caused by digital converters and computer recording latency. This zero-latency analog monitoring is controlled by the Monitor Mix knob, which you can use to adjust the blend between the live analog inputs (called "Direct") and any sounds coming back from the computer via USB ("Playback"). To adjust the playback mix coming back from the computer (previous tracks, effect returns etc. ), use the faders on the Mixer screen of the software. To hear only the live source input signals plugged into the U22, turn the Mix knob fully left to Direct. To hear only the mix from the computer, turn the Mix knob fully right to Playback. The output from the Monitor Mix control is routed to the Line and Headphone outputs. 11. uSB LeD Lights when a USB connection is detected. 4 rear and Side Panels 1 2 3 4 5 6 7 8 1. InStruMent InPut This unbalanced input accepts a 1/4" connector and supports instrument level sources (including guitars). Note that when the Instrument input is connected, the Mic/Line input 1 is disabled. 2. [. . . ] Once you add a track to your Cubase project the Input Routing field will default to U22 In 1. However if you connect instruments to other inputs on the U22 you will need to change the input routing for the track you are recording onto. Please refer to the chart below to see how the input routing labels in Cubase LE 4 correspond to the physical inputs on the U22. Input Routing Labels for Mono Tracks in Cubase LE 4 (When using the Lexicon® I·ONIX U22 Mono In Project Template) U22 In 1 U22 In 2 U22 Input 1 2 17 Audio Mixdown You can use the audio mixdown function in Cubase® LE 4 to create a . wav file from your Cubase project. [. . . ]