User manual LEXICON I-ONIX FW810S

[. . . ] Owner's Manual IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS THE APPARATUS SHALL NOT bE ExPOSED TO DRIPPING OR SPLASHING LIqUID AND NO ObjECT FILLED WITHI LIqUID, SUCH AS vASES, SHALL bE PLACED ON THE APPARATUS. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOvES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT. ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED bY THE MANUFACTURER. Safety InStructIOnS Notice For customers iF Your uNit is equipped With A poWer cord. WArNiNG: this AppLiANce shALL Be coNNected to A mAiNs socKet outLet With A protectiVe eArthiNG coNNectioN. [. . . ] InStruMent ButtOn/LeD Press when an instrument level source (such as a guitar) is connected to the corresponding input (1 or 2). +48V ButtOn/LeD Each of these buttons enables the phantom power to the corresponding inputs pairs. Dynamic microphones do not require phantom power to operate, but are not harmed by it. If you are unsure about the phantom power requirements for your microphone, consult your microphone's documentation or contact the manufacturer. This switch should be OFF if you are connecting any line-level source to the Mic/Inst or Mic Pre jacks. 4. DynaMIcS LeDS anD InPut LeVeL LeDS The top three rows indicate what dynamics are active for each input. The bottom three rows indicate signal presence (green) and level (yellow and red) for each input. 5. fIrewIretM LeD Indicates when a FireWireTM connection is present. 6. GaIn knOBS 1 anD 2 These knobs adjust the input gain levels for Mic/Inst 1 and Mic/Inst 2. 8. GaIn knOBS 3 ­ 8 These knobs adjust the input gain levels for Mic Pre 3 ­ 8 (the inputs located on the back panel). 9. heaDPhOne LeVeL knOB Adjust headphone output signal level here. 11. MaIn OutPutS LeVeL knOB Adjust the main output signal level here. 3 4 rear Panel 12 3 456 7 8 1. MIDI In anD Out The MIDI jacks provide MIDI input and MIDI output to and from your computer. Connect your MIDI keyboards, sound modules, and external controllers here. 4. S/PDIf In anD Out The S/PDIF in and out ports are unbalanced phono (RCA) connectors that transmit and receive either a 16-bit or 24-bit two-channel audio stream. S/PDIF ports may be found on many professional and consumer CD and digital audio recorders. It is recommended to use 75-Ohm coaxial cable for S/PDIF transfers and keep the cable length to a maximum of 10 meters to minimize interference and data dropout. 5. Note: When daisy chaining devices, connect other I-ONIX FW810S units only. BaLanceD OutS 1­8 These outputs support balanced TRS or unbalanced TS ¼" connections. These outputs can be connected to a mixing board, power amplifier, powered studio monitors, recorder, or another line level input. 7. MaIn OutPutS These outputs support balanced TRS or unbalanced TS ¼" connections. These outputs can be connected to a mixing board, power amplifier, powered studio monitors, recorder, or another line level input. 8. [. . . ] Hold is adjustable between 0 to 500 mSec and is dynamically set while in Auto mode. Channel Strip Dynamics ­ Limiter On/Off button Turns the Limiter on or off. Threshold knob The Threshold is the signal level at which the unit begins to limit the signal. If the level is set to -10 dBFS, then any signal larger than -10 dBFS is reduced in gain. The range of the Threshold fader is -60 to +18dBFS. Auto button This button turns Auto mode for the Limiter on and off. Auto mode dynamically sets the Limiter Attack and Release based on the input signal. Attack knob The Attack parameter sets how quickly the Limiter starts to reduce the gain of the signal after it passes the Threshold. [. . . ]