User manual LEXIBOOK SM1960

[. . . ] CHN : pour faire défiler les canaux à distance (Extérieur 1, Extérieur 2 et Extérieur 3); pour faire défiler les canaux locaux et à distance (Extérieur 1, Extérieur 2 et Extérieur 3) en mode d'alarme de température (forte & faible) ; pour activer la fonction de réglage automatique, pour changer le réglage du jour de la semaine en mode d'alarme et pour faire permuter l'affichage de la température entre Cº et Fº. Fixation du capteur à distance et du récepteur Le récepteur (unité principale) est équipé d'un support mural et d'un support inclinable. Pour l'utiliser avec le support inclinable, fixez simplement le support à l'unité principale en « enclenchant » la boule dans le trou situé à l'arrière de l'unité, puis placez-le à l'endroit désiré sur une surface plate et stable. Pour assurer une bonne transmission, le capteur à distance ne doit pas être installé sur ou près d'une large surface métallique. [. . . ] When the main unit's LCD display becomes dim, it indicates that the batteries are low and need to be changed. After batteries have been inserted in the remote sensor, rain gauge, anenometer and in the main unit, the learning function is launched automatically and runs for approximately 3 minutes. Within these 3 minutes, the main unit (receiver) picks up the temperature & humidity signals from the remote sensor and displays the readings. Manual-Learning (Searching for Remote Signals) If a new remote sensor is added or if the signal is lost (outdoor display blinking), the learning function must be executed again. The 'arrow' symbol inside the outside temperature trend box will flash, and unit will beep as each remote sensor is detected. Temperature & humidity readings of the remote sensor and wind direction, wind speed & rainfall readings are displayed on the main unit. Note: Auto/Manual Learn will not operate while the radio controlled clock is receiving DCF77 or MSF signals. Fixing your remote sensor and your receiver The receiver (main unit) has a wall mount holder and a tiltable stand. To use it with the stand, just put the main unit and the stand together by `clicking" the ball in the hole at the bottom of the unit, than put it anywhere you want on a flat and stable surface. To ensure a good transmission, the receiver should not be installed on, or near, a large metal surface. To fix the receiver on a wall, you need first to remove the stand, for that gently pull it, and then you can put it on a hook or nail on a wall. The remote sensor has a detachable cover with both a wall mount holder and a stand. To fix it on a wall, make sure the stand is not pulled out and fix the holder on a hook or nail. To put the remote sensor on a shelf or table, simply pull the stand out and make sure it is well secured and stable. To ensure a good transmission, the remote sensor should not be installed on, or near, a large metal surface. Before choosing the location of the remote sensor, test that the receiver can receive the signals. It is also recommended that the remote sensor is placed as close as possible to the receiver to eliminate any interference. It will stay on for about 6 Generally takes about 10 minutes, depending on the strength of the radio signal. During the reception of the RCC signal, the main unit will no longer update the data received from the outdoor remote sensor, the anenometer and the rain gauge. The scan can also be triggered manually by holding the MINUTE/- key [3] for 3 seconds. When the reception is complete, the Radio Tower symbol will stop blinking and remain solid. For an optimal reception, place the weather station away from metal objects and electrical appliances (i. [. . . ] Also, the amount of precipitation varies so much locally that your area might get a different level of rainfall than the one recorded at your local weather observatory. - The rainfall can be displayed in mm or inches, moreover it can show the rainfall record in total, at last hour, today, and yesterday. Change the display unit: Press Minute/­ [3] to toggle between wind speed in mph with rain fall in inches and wind speed in km/h with rain fall in mm. Display the rainfall record: To display the last hour, today and yesterday's accumulated rainfall: Press HOUR/+ [2] repeatedly to change the rainfall record. [. . . ]