User manual LERVIA KH 9

[. . . ] Ensure that the voltage supplied through the mains socket tallies completely with the details given on the appliance rating plate. · To disconnect, always pull the plug itself out of the power socket, do not pull on the power cable. · Never touch the oil radiator, the power cable or the plug with wet hands. · Under no circumstances may the appliance be submersed in fluids or fluids be allowed to permeate the housing. [. . . ] · ALWAYS position the appliance on a level and heat resistant surface. -2- · Do not place open fire sources, e. g. · Do not use an external timing switch or a separate remote control system to operate the appliance. Description of the appliance 1 Control lamp "Power" 2 Heat level switch 3 Thermostat 4 Warm air switch with integrated warm air control lamp 5 Warm air outlet 6 Cold air intake 7 Power cable retainer 8 Mounting bracket 9 Roller rails 0 Wing nuts Injury hazard · Lay the power cable in such a way that no one can tread on or trip over it. In an emergency the power plug must be quickly accessible. Assembly Use the fold-out page of these instructions to assist you with the assembly. Take the oil radiator and all components from the package and remove all packaging materials. Place the oil radiator, with the base uppermost, on a soft surface, for example a carpet. Place a mounting bracket 8 under the heater element so that the parts with a screw thread project upwards. Lay a roller railer 9 over it, such that the screw threads protrude through the holes. Check to ensure that the recesses on the roller railers 9 face outwards. The screw ends projecting from the appliance must reach into the recesses. Screw one wing nut 0 onto each of the threaded ends of the mounting bracket 8 until it is hand tight. Turn the appliance over and place it on the rollers. Items supplied Oil Radiator 2 Roller rails 2 Mounting bracket 4 Wing nuts Operating instructions Technical data Rated voltage: Heat output: Thermostat: Heating gills: 220­240 V ~ 50 Hz 2300 - 2600 W Infinitely variable 9 -3- Commissioning 1. If you wish to switch the appliance off, first place the warm air switch 4 at the position OFF. Next, turn the heat level switch 2 to "0" and then the thermostat 3 to MIN. Remove the plug from the wall power socket. Note: Ensure that the thermostat 3 and the heat level switch 2 are standing at MIN resp. Place the heat level switch 2 at "III" and the thermostat 3 at MAX. The control lamp "Power" 1 glows. Frost protection function You can programme this oil radiator so that, if the room temperature reaches 0°C, it switches itself on and begins to radiate heat automatically: 1. Position the heat level switch 2 at "I", "II" or "III", and the thermostat 3 at MIN. The oil radiator will now switch itself on if the temperature falls to 0°C. When the temperature rises above 0°C, the oil radiator switches itself off automatically. Important: With the heat level switch 2 you can regulate how quickly the appliance warms up. If you wish to heat it up particularly quickly, select heat level "III", if a slow warming up is preferred, select heat level "I". [. . . ] DES Ltd Units 14-15 Bilston Industrial Estate Oxford Street Bilston WV14 7EG Tel. : 0870/787-6177 Fax: 0870/787-6168 e-mail: support. uk@kompernass. com Irish Connection Harbour view Howth Co. Dublin Tel: 00353 (0) 87 99 62 077 Fax: 00353 18398056 e-mail: support. ie@kompernass. com Disposal Do not dispose of the apliance in your normal domestic waste. This product is subject to the provisions of European Directive 2002/96/EC. Dispose of the appliance through an approved disposal centre or at your community waste facility. [. . . ]