User manual LERVIA KH 1410

[. . . ] Any other usage of, or modification to, the appliance is deemed to be improper usage and carries the risk of serious personal injury. The manufacturer accepts no liability for damages that result from improper use of the appliance or are caused by the incorrect operation of it. · · Prevent the appliance from coming into contact with moisture!Do not place the appliance close to fires, sources of heat or prolonged ambient temperatures of over 50° C!When not in use, disconnect the appliance from the power source and pack the power cord away! [. . . ] Place the desired tool (floor tool e, crevice tool f or upholstery brush g, see chapter , , Changing tools") on the lower end of the telescope tube o. Adjust the telescope tube o to the desired length: Press the height adjustor u down. Pull the telesopic tube o a little further until it audibly engages. Appliance description 1 2 3 4 5 6 7 8 9 0 q w e r t z u i Dust collector carrying grip Unlock button for housing lid Exhaust filter cover Storage bracket for floor tool On/Off switch Vacuum cleaner carrying grip Suction power regulator Foot button for power cable rewind Power cable with power plug Storage bracket for floor tool Housing cover Selector switch for carpet/hard surface Floor tool Storage hook Dust collector Suction pipe connector Height adjuster for telescope tube Storage hook 2. 3. 4. The Cyclone Vacuum Cleaner is now ready for use. -3- Changing tools When you want to change the tool, proceed as follows: 1. To vacuum dust from difficult to reach locations. Attention! Should the red marking on the power cable 9 be visible, rewind the power cable 9, by pressing on the foot button for power cable rewind 8, back to the yellow marking. If you are using the floor tool e, adjust the setting for carpet/hard floor w with the selector switch: · Press the carpet/hard floor selector switch w to the rear for hard floor surfaces such as laminates, tiles and PVC etc. Press the carpet/hard floor selector switch w to the front for carpeted surfaces, such as long or short pile carpets and rugs etc. Floor tool e: Crevice tool f: Upholstery brush g: To vacuum dust from upholstery or other fabric surfaces. Switch the machine off at the On/Off switch 5. Attention! Remove the plug 9 from the wall socket. Store the no longer required tools as far as practicable in the accessory bracket p. · 6. Pull the vacuum cleaner after you like a sledge. When vacuuming, pay heed to the information providet by the floor covering manufacturer. Notice: Should you need to reduce the suction power, e. Hold the power plug 9 firmly and press on the foot button for power cable rewind 8. Allow the power cable 9 to pull itself in slowly. Operation Attention! Before every utilisation check to ensure that all filters are correctly inserted and that no openings are blocked. Pull the power cable 9 from the cable storage up to the yellow marking. -4- Emptying the dust collector Storage · · During work breaks place the storage hook r in the storage bracket 0. If you do not intend to use the vacuum cleaner for an extended period, shorten the telescopic tube o as much as possible and place the storage hook i in the storage bracket 4. If you do not intend to use the vacuum cleaner for an extended period, empty the dust collector t and clean both it and the filters (see the chapters , , Filters" and , , Cleaning and care"). Store the vacuum cleaner at a cool and dry location. · · Empty the dust collector t at the latest when the MAX marking is reached or the suction power has noticeably diminished. Filters The vacuum cleaner has the following filters: · Lamellen filter: For the filtering out of light dust particles. This filter should be cleaned every two months (see chapter , , Lamellen filter"). Motor protection filter: Should the lamellen filter not function properly, the motor protection filter prevents larger dust particles from damaging or destroying the motor. Exhaust filter: For filtering the smallest dust particles from the blown-out exhaust air. This filter should be checked every 6 months. Attention! Before emptying the dust collector t, remove the plug 9 from the power socket. [. . . ] Press the locking device of the exhaust filter cover 3 in the middle and at the same time pull the exhaust filter cover 3 away from the vacuum cleaner to open it. Dispose of the appliance through an approved disposal centre or at your community waste facility. · Power cable 9 is damaged. · Insert the power plug 9 into the power socket. · Arrange for the power cable 9 to be exchanged by authorised specialists. The appliance does not pick up dirt · Dust collecter t is full or · Empty the dust collector t. [. . . ]