User manual LERVIA KH 1148

[. . . ] The proximity of moisture presents a danger, even when the appliance is switched off. · Remove the plug from the power socket in the event of functional irregularity and before cleaning the appliance. · Arrange for damaged or defective power cables, power plugs and appliances to be repaired or exchanged by Customer Services before re-use. · Should the appliance have sustained a fall or be otherwise damaged, it may no longer be taken into use. [. . . ] · Never permit children to use the appliance without supervision from an adult. · Lay the power cable in such a way that no one can tread on or trip over it. · Do not use extension cables. Correct use The Fan Heater serves the purpose of heating and ventilating living areas. This Fan Heater is intended exclusively for use in private households and may only be used for this purpose. To this belongs also the observance of all of the information in these operating instructions, especially the safety instructions. All other uses are deemed to be improper and may result in property damage or even in personal injury. Kompernaß GmbH accepts no liability for damage caused by improper use of the appliance. -5- KH1148_Heiz_IB_UK 10. 08. 2006 11:52 Uhr Seite 6 KH 1148 Delivery content Fan Heater Operating instructions Warranty card · Place the Fan Heater on a level surface. The Fan Heater is now ready for service. Device Overview Safety Carrying handle Switch for the oscillating function Function switch Control lamp Protective grating Safety switch Base Thermostat regulator Tilt cut-out This Fan Heater is fitted with a safety switch . The Fan Heater first switches itself on again when it is in an upright position. Overheating protection The Fan Heater is fitted with overheating protection. Should this happen, check to see if the protective grating is covered or blocked. Wait until it has cooled down before switching it back on. Technical data Mains voltage: Output: Heating level 1: Heating level 2: Protection class: 220-240V ~ 50Hz 1000 W 2000 W II Before the first use · Take the Fan Heater from the transport packaging. To avoid the chance of suffocations, ensure that they do not come into the possession of children. · Check the items to see that they are all present, complete and without any damage. Operation To use the ventilator function: · Place the function switch into the position Fan . To use the heating function: · Place the function switch to the desired heating level, 1 or 2. -6- KH1148_Heiz_IB_UK 10. 08. 2006 11:52 Uhr Seite 7 KH 1148 The fan switches on and the control lamp lights up in red. The Fan Heater is fitted with switching levels: Position 0 Status of the Fan Heater OFF Fan, no heating 1 2 Warm air flow (1000 W) Hot air flow (2000 W) · After every use remove the plug from the wall socket. Room temperature setting · Place the function switch on the desired heating level, 1 or 2. · As soon as the desired room temperature has been reached, turn the thermostat regulator slowly back, until a light resistance is felt and a click is heard. The Fan Heater now switches itself on automatically as soon as the temperature falls below the programmed level. When the temperature in the room falls below the programmed level, the Fan Heater switches itself on automatically. [. . . ] Dispose of the appliance through an approved disposal centre or at your community waste facility. In case of doubt, please contact your waste disposal centre. Warranty and Service The warranty conditions and the service address can be found on the warranty slip. Kompernaß GmbH Burgstrasse 21 D-44867 Bochum www. kompernass. com -8- KH1148_Heiz_IB_UK 10. 08. 2006 11:52 Uhr Seite 9 KH 1148 Troubleshooting Symptom Possible causes and solutions The Fan Heater does not switch itself on. The room temperature is higher than the temperature programmed into the thermostat controller. Arrange for the Fan Heater to be checked by specialists. It is not possible to switch the Fan Heater off. [. . . ]