User manual LENOXX PH301

[. . . ] Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. If the product does not operate normally by following the operating instructions. Adjust only those controls, that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. [. . . ] Inform the customer of the right to bring a complaint to the Federal Communications Commission pursuant to procedures set out in FCC Rules and Regulations Subpart E of Part 68 The telephone company may make changes in its communications facilities, equipments, operations or procedures, where such action is reasonably required in the operation of its business and is not inconsistent with the rules and regulations in FCC Part 68. If such changes can be reasonably expected to render any customer terminal equipment incompatible, the customer shall be given adequate notice in writing, to allow the customer an opportunity to maintain uninterrupted service. RINGER EQUIVALENCE NUMBER (REN): The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your telephone number is called. In most areas, but not all, the sum of the RENs of all devices connected to one line should not exceed five (5. 0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should contact your local telephone company to determine the maximum REN for your calling area. NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, try the following: 1. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. GENERAL The FCC prohibits customer-provided terminal equipment to be connected to party lines or to be used in conjunction with coin telephone service. This phone is hearing aid compatible. 2 IB-PH301(MS)-WM-E-113003 Congratulations for purchasing a Durabrand telephone. Your model PH-301 will provide you with many years of trouble-free enjoyment. INTRODUCTION Your Sales Receipt You will need your sales receipt should you ever need warranty service. You should also save the packing materials if you want to move or ship this set. CAUTION: To avoid the possibility of electrical shock, do not use your phone while in the bathtub or shower or when you are wet. If you accidentally drop the phone into water, first unplug its cord from the modular jack, then remove the equipment from the water. Avoid using this telephone during electrical storms in your immediate area. INSTALLATION INSTRUCTIONS plugged in). Insert one end of the modular plugs of the COILED HANDSET CORD into the HANDSET JACK and the other into the BASE JACK on the BOTTOM of the TELEPHONE BASE (either end can be HANDSET JACK TELEPHONE BASE BASE JACK COILED HANDSET CORD For Desk Use Insert the modular plug of the STRAIGHT TELEPHONE LINE CORD into the modular jack at the BACK of the TELEPHONE BASE (either end can be plugged in). The modular plug at the other end of the STRAIGHT TELEPHONE LINE CORD is for connection to the telephone line jack (either end can be plugged in. ) STRAIGHT TELEPHONE LINE CORD TELEPHONE LINE JACK For Wall Mounting WALL MOUNTING WHEN YOU HAVE A MODULAR WALL PLATE SHORT 4" CORD 1. Insert either plug into the modular jack in the TELEPHONE BASE (at the back of the phone). [. . . ] Put a screw into each hole and leave 3 /16" (5mm) of the head exposed. Put the key hole slots over the screws and slide down to secure phone. 4 Make sure space between holes is 100 mm Drill one hole IB-PH301(MS)-WM-E-113003 TROUBLE SHOOTING PROBLEM No dial tone Phone is dead LIKELY CAUSES 1. If your line is conditioned to accept pulse dialing only, slide PULSE/TONE switch to PULSE position. [. . . ]