User manual LENOVO THINKVISION LT1913P (60AAHAT1EU)

[. . . ] LT1913p Flat Panel Monitor User’s Guide Product numbers 60AA-HAR1-WW First Edition (June 2013) © Copyright Lenovo 2013. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C. F. R. 2. 101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration "GSA" contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. [. . . ] This may harm the coating of the screen area. Detaching the monitor base and stand Step 1: Place the monitor on a soft and flat surface. Step 2: Remove the base and stand from the monitor. Wall Mounting (Optional) Refer to the instructions that come with the base mounting kit. To convert your LCD display from a desk-mounted to a wall-mounted display, do the following: Step 1: Verify that the Power button is turned Off, then disconnect the power cord. Step 2: Lay the LCD display face down on a towel or blanket. Chapter 2. 2-10 Step 3: Remove the base from the monitor, refer to "Detaching the monitor base and stand". Step 4: Attach the mounting bracket from the VESA compatible wall mounting kit (100mm x100mm distance), VESA Mounting Screw M4 x 10 mm. VESA hole Step 5: Attach the LCD display to the wall, following the instructions in the wallmounting kit. For use only with UL Listed Wall Mount Bracket with minimum weight/load: 8kg Chapter 2. 2-11 Chapter 3. Reference information This section contains monitor specifications, instructions to manually install the monitor driver, troubleshooting information, and service information. Monitor specifications Table 3-1. Monitor specifications for type-model 60AA-HA*1-** Dimensions Depth Height Width Panel Size Backlight Aspect ratio Stand VESA mount Image Tilt Supported Viewable image size Maximum height Maximum width Pixel pitch Power input Supply voltage Max supply current 208 mm (8. 19 in. ) 446 mm (17. 55 in. ) 486 mm (19. 13 in. ) 19 in. x 3. 94 in. ) 480. 0 mm (19 in. ) 299. 827 mm (11. 81 in. ) 374. 784 mm (14. 76 in. ) 0. 2928 mm (0. 01 in. ) 90-264VAC (100~240VAC+/-10%) 1. 5 A - Power consumption Note: Power consumption figures are for the monitor and the power supply combined Normal operation Standby/Suspend Off Note: without USB/ Webcam/external speaker Input signal Horizontal addressability <23W <0. 5W (Analog), <0. 5W (Digital) <0. 5W at 100Vac & 240Vac Video input (Analog) Analog Direct Drive, 75 ohm 0. 7V 1280 pixels (max) -- Vertical addressability 1024 lines (max) Clock frequency 205 MHz Chapter 3. 3-1 Table 3-1. Monitor specifications for type-model 60AA-HA*1-** Video input (DVI) Interface Input signal Horizontal addressability DVI VESA TMDS (Panel Link™) 1280 pixels (max) -- Vertical addressability 1024 lines (max) Clock frequency Communications Supported Display Modes VESA DDC Horizontal frequency Vertical frequency Native Resolution Temperature Operating Storage Shipping Humidity Operating Storage Shipping 165 MHz CI 30 kHz - 83 kHz 50 Hz - 76 Hz 1280 x 1024 at 60 Hz 0° to 40° C (32° to 104° F) -20° to 60° C (-4° to 140° F) -20° to 60° C (-4° to 140° F) 10% to 80% non-condensing 5% to 95% non-condensing 5% to 95% non-condensing Chapter 3. 3-2 Troubleshooting If you have a problem setting up or using your monitor, you might be able to solve it yourself. Before calling your dealer or Lenovo, try the suggested actions that are appropriate to your problem. Troubleshooting Problem The words "Out of Range" are shown on the screen, and the power indicator is flashing green. Possible cause The system is set to a display mode which is not supported by the monitor. Suggested action If you are replacing an old monitor, reconnect it and adjust the display mode to within the specified range for your new monitor. If using a Windows system, restart the system in safe mode, then select a supported display mode for your computer. The video signal cable is not connected with the monitor or system completely. Be sure the signal cable is firmly plugged into the system and monitor. "Understanding power management"on page 2-9 "Connecting and turning on your monitor"on page 1-5 "Adjusting your monitor image"on page 2-3 "Adjusting your monitor image"on page 2-3 "Connecting and turning on your monitor"on page 1-5 Reference "Selecting a supported display mode"on page 2-7 • • • • • • Screen is blank and power indicator is orange. The monitor is in Standby/Suspend mode. • • Chapter 3. 3-3 Table 3-2. Troubleshooting Problem The power indicator is orange, but there is no image. Possible cause The video signal cable is loose or disconnected from the system or monitor. This is a characteristic of the LCD technology and is not an LCD defect. Suggested action Be sure the video cable is connected with the system properly. If there are more than five pixels missing, contact the Support Center. [. . . ] Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. [. . . ]