User manual LENOVO L2361P WIDE FLAT PANEL MONITOR

[. . . ] L2361p Wide Flat Panel Monitor User's Guide Product numbers L2361pwA First Edition ( 2009) © Copyright Lenovo 2009. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C. F. R. 2. 101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration "GSA" contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. [. . . ] Remove grease or finger marks with a damp cloth and a little mild detergent. Use flammable cleaning materials to clean your monitor or any other electrical equipment. Use any cleaner which contains an anti-static solution or similar additives. This may harm the coating of the screen area. Wall Mounting(Optional) Refer to the instructions that come with the base mounting kit. To convert your LCD display from a desk-mounted to a wall-mounted display, do the following: Step 1: Verify that the Power button is turned Off, then disconnect the power cord. Step 2: Lay the LCD display face down on a towel or blanket. Step 3: Revolve the stand and insure it is parallel to top of the back side. Remove the plastic Covers from the back of the LCD display. Step 4: Attatch the mounting bracket from the VESA compatible wall mounting kit (100mm x100mm distance). Step 5: Attach the LCD display to the wall, following the instructions in the wall-mounting kit. Chapter 2. 2-9 Chapter 3. Reference information This section contains monitor specifications, instructions to manually install the monitor driver, troubleshooting information, and service information. Monitor specifications Table 3-1. Monitor specifications for type-model Dimensions Height Depth Width Stand VESA mount Tilt Supported 442. 0 mm (16. 61 in. ) 118. 0 mm (4. 65 in. ) 569. 0 mm (22. 40 in. ) Range: 10°, 60° 100mm x 100mm (3. 94 in. x3. 94 in. ) Make sure the light bar is located downside when using VESA mount setup. 584. 2 mm(23 in. ) 312. 0 mm (12. 28 in. ) 533. 2 mm(20. 99 in. ) 0. 265 mm (0. 01 in. ) (V) 90-264VAC (100~240VAC+/-10%) 1. 5 A < 45 W <1W(Analog), < 1W(Digital) < 0. 5W at 100Vac & 240Vac Image Viewable image size Maximum height Maximum width Pixel pitch Power input Supply voltage Max supply current Power consumption Note: Power consumption figures are for the monitor and the power supply combined. Normal operation Standby/Suspend Off Note:without Audio in/USB/Webca m Input signal Horizontal addressability Vertical addressability Clock frequency Video input (Analog) Analog Direct Drive, 75 ohm 0. 7V 1920 pixels (max) 1080 lines (max) 205 MHz - © Copyright Lenovo 2009. Monitor specifications for type-model Video input (Digital) Interface Input Signal Horizontal addressability Vertical addressability Clock frequency Communications Supported Display Modes (VESA Standard modes between noted ranges) Temperature VESA DDC Horizontal frequency Vertical frequency Native Resolution Operating Storage Shipping Humidity Operating Storage Shipping HDMI VESA TMDS (Panel LinkTM) 1920 pixels (max) 1080 lines (max) 165 MHz CI 30 kHz - 83 kHz 50 Hz - 75 Hz 1920 x 1080 at 60 Hz 0° to 40° C (32° to 104° F) -20° to 60° C (-4° to 140° F) -20° to 60° C (-4° to 140° F) 8% to 80% non-condensing 5% to 95% non-condensing 5% to 95% non-condensing 3-2 L2361p Wide Flat Panel Monitor User's Guide Troubleshooting If you have a problem setting up or using your monitor, you might be able to solve it yourself. Before calling your dealer or Lenovo, try the suggested actions that are appropriate to your problem. Troubleshooting Problem The words "Out of Range" are shown on the screen, and the power indicator is flashing white. Possible cause The system is set to a display mode which is not supported by the monitor. Suggested action If you are replacing an old monitor, reconnect it and adjust the display mode to within the specified range for your new monitor. If using a Windows system, restart the system in safe mode, then select a supported display mode for your computer. The video signal cable is not connected with the monitor or system completely. Be sure the signal cable is firmly plugged into the system and monitor. "Understanding power management" on page 2-8 "Connecting and turning on your monitor" on page 1-4 "Adjusting your monitor image" on page 2-3 "Adjusting your monitor image" on page 2-3 "Connecting and turning on your monitor" on page 1-4 Reference "Selecting a supported display mode" on page 2-7 · · · · · · Screen is blank and power indicator is flashing white The monitor is in Standby/Suspend mode · · Chapter 3. 3-3 Table 3-2. Troubleshooting Problem The power indicator is white, but there is no image. [. . . ] Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. [. . . ]