User manual LEISURE H91PK

[. . . ] „„ In order to assist in the use of this product, carefully read the User's Manual. „„ For quick set-up of the product, read the Quick Installation Guide included with the product. „„ For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] Automatic mode allows the BIOS to enable all CPU cores (number of cores available depends on the CPU being used). (Default: Automatic mode) && APM Enables or disables Application Power Management. (Default: Enabled) && Extreme Memory Profile (X. M. P. ) (Note 2) && AMD Memory Profile (A. M. P. ) (Note 2) Allows the BIOS to read the SPD data on XMP memory module(s) to enhance memory performance when enabled.  Allows the BIOS to read the SPD data on AMP memory module(s) to enhance memory performance when enabled. (Default: Auto) This value is automatically adjusted according to the BCLK/PCIe Clock Control and System Memory Multiplier settings. && System Memory Multiplier && Memory Frequency (MHz) `` Advanced Memory Settings &&  xtreme Memory Profile (X. M. P. ) (Note 2), System Memory Multiplier, Memory E Frequency(MHz) The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu. (Note 1) This item is present only when you install a CPU that supports this feature. (Note 2) This item is present only when you install a CPU and a memory module that support this feature. - 19 - && DRAM Timing Selectable && Profile DDR Voltage Quick and Expert allows the memory timing settings below to be configurable. When using a non-XMP memory module or Extreme Memory Profile (X. M. P. ) is set to Disabled, this item will display as 1. 50V. When Extreme Memory Profile (X. M. P. ) is set to Profile1 or Profile2, this item will display the value based on the SPD data on the XMP memory. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability. Use <Enter> to switch between the Hour, Minute, and Second fields and use the <Page Up> or <Page Down> key to set the desired value. Displays the current access level depending on the type of password protection used. (If no password is set, the default will display as Administrator. ) The Administrator level allows you to make changes to all BIOS settings; the User level only allows you to make changes to certain BIOS settings but not all. - 21 - && Access Level 2-4 BIOS Features && Boot Option Priorities &&  ard Drive/CD/DVD ROM Drive/Floppy Drive/Network Device BBS Priorities H Specifies the overall boot order from the available devices. For example, you can set hard drive as the first priority (Boot Option #1) and DVD ROM drive as the second priority (Boot Option #2). The list only displays the device with the highest priority for a specific type. For example, only hard drive defined as the first priority on the Hard Drive BBS Priorities submenu will be presented here. Removable storage devices that support GPT format will be prefixed with "UEFI:" string on the boot device list. To boot from an operating system that supports GPT partitioning, select the device prefixed with "UEFI:" string. Or if you want to install an operating system that supports GPT partitioning such as Windows 7 64-bit, select the optical drive that contains the Windows 7 64-bit installation disk and is prefixed with "UEFI:" string. Specifies the boot order for a specific device type, such as hard drives, optical drives, floppy disk drives, and devices that support Boot from LAN function, etc. [. . . ] Step 1: Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the message "Press F6 if you need to install a 3rd party SCSI or RAID driver. " A screen will then appear asking you to specify an additional SCSI adapter. Step 2: Insert the floppy disk containing the SATA RAID/AHCI driver and press <Enter>. Select AMD AHCI Compatible RAID Controller-x86 platform and press <Enter>. Step 3: On the next screen, press <Enter> to continue the driver installation. [. . . ]