User manual LEICA LP C SOFTWARE INSTALLATION MANUAL REV 2

[. . . ] LabeLase® Producer Software installation manual for Cassette Printer Revision 2 30. Read carefully before working with the instrument. Table of Contents Copyright © 2007 InfoSight Corporation All rights reserved InfoSight ® is a registered trademark of InfoSight Corporation LabeLase ® is a registered trademark of InfoSight Corporation InfoSight Corporation 20700 US HWY 23 Chillicothe, Ohio 45601 USA Telephone: 001-740-642-3600 website: http://www. infosight. com eMail: service@infosight. com LabeLase® Producer - Installation 3 Table of Contents LabeLase® Producer Software Installation Manual for Leica LP C ­ Cassette Printer 1. Software/firmware licensing agreement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Each menu is described in more detail below. File Menu The file menu provides access to the program functions that deal with loading cassette layout files for editing, saving layout files, printing reports, etc. If you have changed the current layout without saving your changes, the program will prompt you to save first. You may choose to create a blank layout, load a layout template, or use the "WIZARD" to create the layout. Open - Allows you to open a cassette layout saved on your PC's hard disk drive, a floppy drive, or a network shared folder. Fig. The file is saved using its current name, in the folder from which it was loaded. If the file does not have a name, a Save dialog will prompt you to enter a name and destination folder. Save As - Allows you to save the layout with a different name and/or a different destination folder. Leica LP C 115 3. User Interface Print - Prints a representation of the layout to a printer connected to your PC or to your local network. Print Setup - Allows you to specify the printer to use for printing layout reports. Report - Allows you to view and print a report of the currently loaded layout. You will have the option of printing the report or saving it to a file. Between the Print Setup menu item and the Exit item is a list of up to 4 layout filenames. The program keeps track of the last four layouts loaded by the supervisor and allows them to be re-loaded quickly by clicking on the filename. Edit Menu The Edit menu gives you the ability to perform various editing operations on the cassette layout. Undo - This menu item is available after you have made a change to the layout, such as moving, rotating or resizing a field. When you select Undo, your last change will be rolled back by one step. If you made a change to multiple selected fields, each field's change will be undone separately. Redo - This menu item allows you to repeat or restore changes that you previously have undone. If you have not undone any changes, then there will be nothing to redo, as shown in this example. Cut - Delete the selected field and place it on the program's clipboard. If more than one field is selected, then each is placed on the clipboard. If more than one field is selected, then each is placed on the clipboard. User Interface Paste - Paste the fields in the clipboard to the layout. If no items are in the clipboard, then this menu item is not accessible. [. . . ] With this dialog, you can: · Jog the Print Motor by single (or multiple) steps in either the forward or reverse directions. · Specify a specific position relative to the home sensor and have the motors move there. · Monitor the state of the home sensors to determine if the sensors are functioning properly. Reverse Button - This button will cause the motor to move in the left direction by the number of steps specified in the Number of Steps drop down list. [. . . ]