User manual LEGRAND 845 07

[. . . ] Foundry Networks, EdgeIron, FastIron, IronView, JetCore, NetIron, ServerIron, TurboIron, IronWare, EdgeIron, IronPoint, the Iron family of marks and the Foundry Logo are trademarks or registered trademarks of Foundry Networks, Inc. All other trademarks mentioned in this document are the property of their respective owners. Contents Chapter 1. 2-5 March 2006 © 2006 Foundry Networks, Inc. iii Foundry EdgeIron User Guide Enabling SNMP Management Access . . 4-3 iv © 2006 Foundry Networks, Inc. March 2006 Contents Main Menu . [. . . ] · sfp-preferred-auto - Uses SFP port if both combination types are functioning and the SFP port has a valid link. Default Setting sfp-preferred-auto Command Mode Interface Configuration (Ethernet) Example This forces the switch to use the built-in RJ-45 port for the combination port 24. Console(config)#interface ethernet 1/24 Console(config-if)#combo-forced-mode copper-forced Console(config-if)# giga-phy-mode (EdgeIron 24G-A, 48G only) This command forces two connected ports in to a master/slave configuration to enable 1000BASE-T full duplex. Syntax giga-phy-mode mode no giga-phy-mode · mode · master - Sets the selected port as master. March 2006 Interface Commands Command Mode Interface Configuration (Ethernet) Example This forces the switch port to master in a master/slave configuration. Console(config)#interface ethernet 1/24 Console(config-if)#giga-phy-mode master Console(config-if)# shutdown Use this command to disable an interface. Syntax shutdown no shutdown Default Setting All interfaces are enabled. Command Mode Interface Configuration (Ethernet, Port Channel) Command Usage This command allows you to disable a port due to abnormal behavior (e. g. , excessive collisions), and then reenable it after the problem has been resolved. Example The following example disables port 5. clear counters Note: This command is available on devices running 2. 2. 6. 23 Use this command to clear statistics on an interface. Syntax clear counters interface interface · ethernet unit/port - unit - This is device 1. · port-channel channel-id (Range: 1-6) Default Setting None March 2006 © 2006 Foundry Networks, Inc. 17-19 Foundry EdgeIron User Guide Command Mode Privileged Exec Command Usage Statistics are only initialized for a power reset. This command sets the base value for displayed statistics to zero for the current management session. However, if you log out and back into the management interface, the statistics displayed will show the absolute value accumulated since the last power reset. (Range: 15-1440 minutes; Default: 15 minutes) Default Setting Status: Disabled Command Mode Global Configuration Command Usage By default, learned secure MAC addresses are not saved to the startup configuration file. Use this command to enable the periodic saving of secure MAC addresses to the startup file. Example The following example enables the port security autosave feature, and sets the update interval to 100 minutes. Console#configure Console(config)#port security autosave 100 Console(config)# port security (EdgeIron 2402CF and EdgeIron 4802CF) Use this command to enable and configure port security on a port. Use the no form to disable port security and reset the maximum addresses to the default. Syntax port security [max-mac-count address-number] no port security [max-mac-count] address-number - Sets the maximum number of MAC addresses that can be learned on a port. (Range: 0 - 20) 17-22 © 2006 Foundry Networks, Inc. March 2006 Interface Commands Default Setting Status: Disabled Maximum Addresses: 0 Command Mode Interface Configuration (Ethernet) Command Usage · If you enable port security on a specified port, the switch will dynamically learn MAC addresses until the specified number has been reached and then stop. Only incoming traffic with source addresses already stored in the dynamic or static address table will be accepted. · To use port security, specify a maximum number of addresses to allow on the port and then let the switch dynamically learn the <source MAC address, VLAN> pair for frames received on the port. You can also manually add secure addresses to the port with the mac-address-table static (20-2) command. · First use the port security max-mac-count command to set the number of addresses, and then use the port security command to enable security on the port. · Use the no port security max-mac-count command to disable port security and reset the maximum number of addresses to the default. [. . . ] Protected Extensible Authentication Protocol (PEAP) A protocol proposed by Microsoft, Cisco and RSA Security for securely transporting authentication data, including passwords, over 802. 11 wireless networks. Like the competing standard Tunneled Transport Layer Security (TTLS), PEAP makes it possible to authenticate wireless LAN clients without requiring them to have certificates, simplifying the architecture of secure wireless LANs. Rapid Spanning Tree Protocol (RSTP) RSTP reduces the convergence time for network topology changes to about 10% of that required by the older IEEE 802. 1D STP standard. March 2006 © 2006 Foundry Networks, Inc. Glossary-5 Foundry EdgeIron User Guide Remote Authentication Dial-in User Service (RADIUS) RADIUS is a logon authentication protocol that uses software running on a central server to control access to RADIUS-compliant devices on the network. Remote Monitoring (RMON) RMON provides comprehensive network monitoring capabilities. [. . . ]