User manual LEGO 7030

[. . . ] When not in use, tools must be locked up in a dry location to inhibit rust. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool's capacities. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. [. . . ] When the equipment is operated outdoors, use only extension cords intended or outside use. See chart under "Extension Cords: for the proper AWG rating depending on the length of the cord(s) being used. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. Sockets built for impact wrenches are specifically designed to withstand the force of the delivered blow. Any other socket may shatter, causing injury to the operator and damage to any nearby equipment. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. In addition, people with pacemakers should: · Avoid operating alone. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. 4. 7. 8. RECOMMENdEd MINIMuM WIRE gAugE FOR EXTENSION CORdS* (120/240 VOLT) NAMEPLATE AMPERES (at full load) 0 ­ . 0 . 1 ­ 3. 4 3. ­ . 0 . 1 ­ 7. 0 7. 1 ­ 1. 0 1. 1 ­ 1. 0 1. 1 ­ 0. 0 EXTENSION CORd LENgTH 25 Feet 18 18 18 18 18 14 1 50 Feet 18 18 18 1 14 1 10 75 Feet 18 18 1 14 1 10 - 100 Feet 18 1 14 1 10 - 150 Feet 1 14 1 1 - TABLE A * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ A Volts Alternating Current Amperes No Load Revolutions per Minute n0 xxxx/min. (RPM) SKU 7030 For technical questions, please call 1-800-444-3353. Page SPECIFICATIONS Motor Power Drive 10 V~, 0 Hz, 7 A; 100 RPM 2400 BPM: 240 ft-lb Torque 1/" 230373 uNPACkINg When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. OPERATINg INSTRuCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. general guidelines 1. You may use impact socket adapters to use impact sockets with drives greater than 1/ ". Pressing the top of the ROCKER SWITCH () up will cause the ANVIL (1) to move in a counterclockwise direction. 4. Rocker Switch (# ) . Figure 1 -- operation Pressing the bottom of the ROCKER SWITCH down will cause the ANVIL to move in a clockwise direction. This will commonly tighten the fastener. "Breaking Loose" Fasteners Note: This procedure is used when a fastener becomes "frozen", typically due to corrosion. This procedure assumes that the threads are standard (clockwise to tighten, counter clockwise to loosen). If the threads are reversed, you must reverse the switch directions contained herein. [. . . ] Fits on bearing O. D. SKU 7030 For technical questions, please call 1-800-444-3353. Page 9 ASSEMBLY dIAgRAM Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 7030 For technical questions, please call 1-800-444-3353. Page 10 LIMITEd 90 dAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. [. . . ]