User manual LAZERBUILT FULL-DUPLEX CONFERENCE PHONE

[. . . ] Volume Control A control is provided to adjust the volume of the received speech. Recall A recall button is provided to activate network services such as call waiting or may be used in conjunction with a PABX to transfer calls. Mute Turn off the microphone so that the person at the other end does not hear you speak. Extension Microphone (optional extra) For the larger conference room, provision is made for a second microphone, which may be placed up to 15 feet from the conference unit. Product Features Internal Microphone : Used for talking into the conference phone. [. . . ] 1 Set the switch to the Tone position 2 Turn the unit ON (ON/OFF button) and listen for dial tone. 3 Dial a known number (remember to include any line access digit required by the PABX usually 9). 4 If the call is successful (ringing or engaged tone) the switch may be left in the Tone position. If the call is unsuccessful, terminate the call by pressing the ON/OFF button. Set the switch to the Pulse position and try the test above again. Using the Tone Button If you have set the Tone / Pulse switch to the Pulse position, you may temporarily change to Tone dialling by pressing the Tone button. This may be required when accessing automated telephone services, which require Tone signals. Setting the Ringer Volume Your Summit conference phone will ring for incoming calls. The Ringer Volume Switch may be used to adjust the volume of the ringer between High, LOW or OFF. With the switch set to the OFF position, the unit will not ring for incoming calls but can still be used to make outgoing calls, or to answer incoming calls ringing on a parallel extension phone Operation Making a Call Using the Summit Conference Phone 1 Press the ON/OFF button and listen for dial tone. 2 Dial the required number on the keypad (when connected to an extension of a PABX, remember to include any line access digit required). 3 When the other party answers, you may conduct a conversation using the built-in microphone. you would like another partly to listen in to a conversation or discussion you are having, but not be able to take part in it. Mute The Summits microphone(s) may be turned off, by pressing the Mute button. This will still allow you to hear the other party but they will not be able to hear you. Note : If you have installed the optional extension microphone, this will also be muted. Receive Volume You may adjust the volume of receive speech, by pressing the UP and DOWN buttons. When you have reached the maximum or minimum positions, the unit will beep 3 times. As this beep may be quite loud over the telephone line, it is recommended that you advise the other party before adjusting the volume. Note : With the volume in the minimum position, the incoming speech will be very quiet. This position may be useful if you wish To Answer an Incoming Call Calls may be answered on the Summit conference phone by pressing the ON / Off button, (the Mute and Volume buttons will work in the normal way). The ON / OFF button should be pressed again when the call is completed. Operation Making a Call using a Parallel Telephone You can also make a call on a parallel (extension) telephone and then transfer the call to the Summit conference phone. When you wish to transfer the call, press the ON / OFF button on the conference unit and hang up the telephone by returning the handset to its cradle. Caution : If you do not hang up the telephone, you may experience a whistling noise caused by feedback between the 2 products. Recall The Summit conference phone generates a recall signal for use when connected to an office PABX (transferring or placing calls on hold etc. ) or when accessing additional network services such as call waiting. With the Pulse / Tone switch set in the Pulse position, the unit will generate an Earth recall. With the switch set to the Tone position, the unit will generate a Timed Break Recall (TBR) of approximately 100mS. Ringer Equivalence Number (REN) If you connect too many devices to your telephone line, they may not ring correctly. [. . . ] Complies with the European RTTE directive Complies with the European EMC directive 89/336/EEC. If it becomes faulty within the guarantee period but after the first month, it should be returned for repair to Lazerbuilt (at the address shown above), either directly or via your retailer. After the guarantee period, return your product to Lazerbuilt, indicating the problems you are experiencing. Include your name, address, telephone number and a postal order/cheque for £5. 00 to cover the handling charge. [. . . ]