User manual LAUNCH X-431

[. . . ] LAUNCH X-431 User's Manual Trademark Information LAUNCH is a registered trademark of LAUNCH TECH. All other LAUNCH trademarks, service marks, domain names, logos, and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos, company names of or are otherwise the property of LAUNCH or its affiliates. In countries where any of the LAUNCH trademarks, service marks, domain names, logos and company names are not registered, LAUNCH claims other rights associated with unregistered trademarks, service marks, domain names, logos, and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. [. . . ] If the To Do has been finished, please click the box to the right of `Finished'. In the To Do Detail interface, click [OK] button to save and close the To Do New interface. Figure 4-26 1) 2) 3) In the pop-up `PIM' list, select `To Do' item to open the To Do interface. The To Do list of corresponding items will be displayed in the list box on the midst of the Memo interface. Click [Options] button to open the To Do 39 8) 9) LAUNCH X-431 User's Manual 2) 3) 4) 5) 6) 7) in the interface so that the type list pops up. In the type list, select `Edit Group' to open the Edit Group interface. In the text box at the bottom of the interface, input the name of the type. Click [New] button to add a new type and it will be displayed in the list box of the Edit Group interface. Select one type in the list box, and then click [Delete] button to delete it. Click [Close] button to close the Edit Group interface. Figure 4-28 View To Do 1) In the list box of the To Do interface, click the to do that you want to view. 2) Then the contents of the To Do will be shown in the opened To Do Edit interface. Edit To Do 1) In the list box of the To Do interface, click the memo that you want to edit. 2) Then the contents of the memo will be shown in the opened To Do Edit interface. 3) Click [Detail] button to open the To Do Detail interface, please refer to step 4~8 in the section "Add New To Do". 4) After editing, click [OK] button to save the edited contents and close the To Do Edit interface. Delete To Do 1) In the list box of the To Do interface, click the to do that you want to delete. 2) Then the contents will be shown in the opened To Do Edit interface. 3) Click [Delete] button to delete the To Do and close the To Do Edit interface. Edit Type 1) Click the [] button to the right of `Group' 40 The interface : It represents the To Do Detail Interface (Refer to step 1-3 in the section "Add New To Do" and "Edit To Do"), and the To Do Display interface (Refer to step 1 in the section "The Set of Display "). Figure 4-29 LAUNCH X-431 User's Manual The Set of display Figure 4-31 Figure 4-30 1) 1) 2) In the To Do interface, click [Options] button to open the To Do Display interface. In the To Do Display interface, click the button to the right of `Group' to pop up type list, and select the type in the pop-up list. Click the button to the right of `Expired', and select the data in the pop-up list. Click the number or `All' to the right of `Priority' to set the priority of the displayed To Do. (See Figure 4-30) Click [OK] button to close the To Do Display interface. [. . . ] 00002 Power cut owing to undervoltage when the inputted voltage for adaptation is reached. Code 00002 is entered according to customer's request; For auxiliary heating device of which the spare part No. can be read out by our scan tool in the function like [Read ECU memory]; Power cut will be caused by undervoltage whenever the code is 00001 and the voltage of auxiliary heating device is lower than the battery voltage for adaptation of basic setting; Power cut will be caused by undervoltage whenever the code is 00002 and the voltage of auxiliary heating device is lower than the battery voltage inputted for adaptation. If the fault message like "Power cut owing to undervoltage (constant value)" is displayed for auxiliary heating device (code is 00001), please perform the following steps: 1) Change the code of auxiliary heating device to 00002 and confirm the control unit code; 2) Read out the inputted value (constant value) of uncervoltage power cut by means of the 77 LAUNCH X-431 User's Manual function [Adaptation] and then perform adaptation; 3) Alter the constant value by means of the function [Adaptation] (Specified value is below 10. 5V); 4) Change the code of auxiliary heating device to 00001. [. . . ]