User manual LARSON WOOD CORE

[. . . ] 202220567 LM 5/03 WOOD-CORE Series Installation Instructions Before You Get Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 2­9 Closure Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 8­9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10 Warranties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11 General Care and Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12 Visit our web site at www. larsondoors. com Congratulations!You've purchased a quality-built wood core storm/screen door from Larson. Please take a moment to fill out and mail in your product warranty card for years of trouble-free service. If you have any questions regarding the installation of your Larson storm door or need to order replacement parts, do not go back to the store, call our Homeowner's Helpline at 1-888-483-3768. [. . . ] Pull rod out of closer so that there is a approximately 1/4" gap per Figure 1 (insert small screwdriver in rod hole to provide pulling grip). Attach closer rod to side jamb bracket (short connecting pin) with open side of jamb bracket toward storm door (see arrow on bracket). Close and latch door. FIGURE 1 1/4" "HOLD OPEN" WASHER CLOSER FLANGE EXTEND ROD 1/4" OUT 1a One Closer Models CLOSER ASSEMBLY INSTALLATION: 1. To install the closer, hold closer assembly 3" below door window and hold jamb bracket 1/4" back from storm door. Fasten jamb bracket to jamb with four #10x1-1/2" screws (see Figure 3). The open side of the jamb bracket should be toward the storm door (see arrow on bracket). Hold the closer and door bracket level and mark the location for the insertion of the door bracket screws. Slide hold-open washer over flanges toward cylinder on closer. FIGURE 2 *OPTIONAL: Closer can be installed at the top of the door on (1-closer) models if desired. 1/4" FROM DOOR SIDE JAMB BRACKET HINGE SIDE JAMB SHORT CONNECTING PIN 1 CLOSER MODELS: 3" BELOW WINDOW OPENING LONG CONNECTING PIN 1/4" H NC PI 1b Two Closer Models 1. To install the top closer, hold closer assembly 1-1/2" above door window and hold jamb bracket 1/4" back from storm door. Fasten jamb bracket to jamb with four #10x1-1/2" screws (Figure 3). The open side of the jamb bracket should be toward the storm door (see arrow on bracket). Hold the closer and door bracket level and mark the location for the insertion of the door bracket screws. Drill 1/8" starter holes. CAUTION: Do not drill through the outside of door. To install bottom closer, hold assembly level 1" above the expander and hold jamb bracket 1/4" from storm door. NOTE: Bottom closer may need to be applied over the door expander in some cases. 8 202220567 WOOD CORE SERIES DOOR BRACKET INTERIOR VIEW LOOKING OUT CLOSER DOOR BRACKET SCREWS 2 CLOSER MODELS: 11/2" ABOVE WINDOW (TOP CLOSER) 1" ABOVE EXPANDER (BOTTOM CLOSER) FIGURE 3 #12 x 5/8" ROUND HEAD #10 x 1-1/2" ROUND HEAD LONG PIN SHORT PIN 2 Controlled Latching Power Feature 3 Wind Safety Chain Installation Installed as directed, with door bracket connected to the FRONT hole of closer, the door will accelerate its closing speed in the last few inches of travel. This attachment position is recommended when the glass storm panel is in place. If a smoother, quieter closing action is desired, hold door open about 8" with hold-open washer. On two closer models, adjust each closer individually (with the other closer disconnected from the door) to the closing speed sufficient to latch the door. The closing speed for each closer should be the same. FIGURE 4 NOTE: Some models do NOT come with a safety chain. To attach safety chain, position the header bracket on the head jamb 18" in from the hinge side of the door frame and 1-1/2" back from the front of jamb (Figure 5). Mount this bracket at approximately 45 degrees (pointing towards door bracket when door is open). Mark location of the holes and drill two pilot holes with a 1/8" bit about 3/8" deep. [. . . ] Using a soft, clean cloth, apply the cleaner, and clean only a small portion of the surface at one time. For heavy cleaning use regular SoftScrub (SoftScrub with Bleach may slightly abrade surface), Bug and Tar Remover, or OOPS. Never use Acetone, or products containing esters, ethers, ketones, aromatic and chlorinated hydrocarbons. For stain removal (white surfaces only), apply liquid bleach to a paper or cloth towel. [. . . ]