User manual LARSON EZ100-200

[. . . ] On the end shown, slide both the screen roll and pull bar 1/8" into the cassette. Hold the cassette and pull bar together and cut the other end to your adjusted measurement from step 2. Note: To avoid unwinding the screen mesh, cut with the saw blade in the direction indicated. Spring Pull Bar Cut With Saw Blade In This direction Cut This End Cassette In Sl i 1 wade /8 r "d Hold the unit upright and carefully tap to clean out any metal shavings. 1/8" Cut length = (H) - 11/16" 6 Spring Installation Insert the spring assembly into the cassette. Slide the bushing into the screen roll making sure the tooth on the bushing lines up with one of the slots in the screen tube. Support the other end of the cassette and rotate the end cap clockwise 12 to 14 turns. [. . . ] Double screens: Drill four 1/8" holes (1" deep) evenly spaced, on both the top and bottom rails. Note: Press the view spreader into the rail to separate the brush pile during screw installation. Drill On Groove Line 2 Screws Evenly Spaced Secure with screws (see screw illustration below). #8 x 1" Phillips Pan Head Drill Two 3/16" Drainage Holes SINGLE SCREENS DOUBLE SCREENS DOUBLE SCREENS ONLY 15 Slide Bolt Lock Installation Slide Bolt Slide Bolt Lock Screw Extend the passive screen until the magnet is centered in the entryway opening. Position a slide bolt lock onto the bottom rail, aligned with the slide bolt. Drill 3/32" pilot hole into the bottom rail and secure with a screw. Repeat for the top slide bolt lock. Care and Maintenance Clean the screen occasionally with mild soap and water. A little care will help insure smooth, gentle operation of your UltraBreeze Retractable Screen. Trouble Shooting Guide Problem Cassette will not secure into mounting clips. Threshold has a steep slope and bottom guide is at an angle, or does not lay flat. Solution Insert back corner of cassette into the mounting clip, then rotate the cassette into the front of the mounting clip to lock in place. Secure wedges or shims under the bottom rail as necessary to hold level. Verify the rounded profile of the cassette faces out (visible from the outside). On double screen units, verify the slide bolt strikes are installed properly and not interfering with top and bottom rails. You will need to remove the assembly, and unattach the spring assembly (step 6) Caution - hold onto the end cap tightly as it is under tension and will unwind. Clockwise to tighten tension and speed up screen or counterclockwise to loosen tension and slow down screen. Crimp the ends of the channels on the top and/or bottom rail to lock the brush pile in place. Screen binds or will not retract into the cassette properly. Screen retracts too fast or too slow. Screen falls out of the top guide. Screen is torn. Page 4 EZ100 Single Screen EZ200 Double Screen OUTSIDE MOUNT INSTALLATION INSTRUCTIONS Assembly Tools Required: Phillips Screwdriver Needle Nose Pliers Pencil Measuring Tape Utility Knife Soft Mallet Drill with Assorted Bits Hacksaw with a Square or Miter Box Power Miter/Chop Saw (Preferred over hacksaw) 2 INSTALLATIONS ONLY 3 12 11 10 9 1 8 17 16 1 Cassette Installation Questions?Replacement Parts? 2 Pull Bar (attached to 1) 3 Top Rail 4 Latch Rail 5 Magnet Strip (attached to 4) Please Call Our Homeowner Helpline 1-888-483-3768 6 Bottom Rail 7 Spring Assembly 8 End Cap 9 Bushing 10 Plug 11 Screw (2) #6 x 3/4" 14 13 15 16 Cautions: Read notes below before beginning 12 Pull Bar End Cap 13 Outside Handle 14 Inside Handle 15 Outside "L" Bracket 16 Screw (10) #8 x 1" 17 View Spreader 7 11 10 15 16 16 12 6 4 5 A. This is not a safety screen and this product will not stop a child from falling out. Read the complete installation instructions before beginning. 1 Installation Methods Single screen installation: Install on either the left or right side. Double screen installation: Install both a left and right screen with one side set up as active screen and the other as passive screen. Active screen is used most often, while passive screen is locked in place until needed. Slide the bushing into the screen roll making sure the tooth on the bushing lines up with one of the slots in the screen tube. Support the other end of the cassette and rotate the end cap clockwise 12 to 14 turns. CAUTION - Do NOT let go of the end cap until it is secured into the cassette. [. . . ] Slide the top and bottom rails onto the tabs protruding from the cassette end caps. Double screens: Drill four 1/8" holes (1" deep) evenly spaced, on both the top and bottom rails. Drill 3/8" holes through the face of the rails using the pre-drilled 1/8" holes as a guide. This will allow the screw to be attached and be covered with the rubber plugs provided. Note: Press the "view" spacer into the rail to separate the brush pile during screw installation. 4 Screws Evenly Spaced 4 Screws Evenly Spaced Drill On Groove Line 2 Screws Evenly Spaced Drill Two 3/16" Drainage Holes SINGLE SCREENS DOUBLE SCREENS Secure with screws (see screw illustration below). [. . . ]