User manual LARSON CLASSIC-VIEW

[. . . ] CLASSIC-VIEWTM Storm/Screen Doors INSTALLATION INSTRUCTIONS Before You Get Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 2­9 Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7 Closer Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 8-9 General Care and Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11 Visit our web site at www. larsondoors. com NOTE: Larger parts may need to be ordered at the store. Congratulations!Please take a moment to fill out and mail in your product warranty card for years of trouble-free service. Larson offers you one of the most liberal warranties in the industry (see page 6 for warranty information). If you have any questions regarding the installation of your Larson storm door or need to order replacement parts, don't go back to the store, call our Homeowner Helpline at 1-888-483-3768. [. . . ] Using #8x1" painted pan head screws, attach the latch-side Z-bar to the wood jamb using the Z-bar's pre-drilled holes as a guide. Do not over-tighten screws. UNDERSIDE OF DRIP CAP TO TOP OF SILL 11 CUT LINE Seal Frame with Caulking (optional) Although not always necessary, you can apply caulking behind the Z-bars (latch, hinge, and top), or along front edge of Z-bar (Figures 12 & 16). 12 Adjust the Bottom Expander FIGURE 19 Adjust the bottom expander so that the vinyl sweeps touch the door threshold. The slotted holes in the expander should be located on the inside of the door. Centrally locate the two #6x3/8" pan head screws (Figure 19) in the slot to allow for future adjustments. Drill 3/32" diameter pilot holes for the screws, being careful not to drill all the way through to the front face of the door. #6 x 3/8" PAN HEAD STAINLESS 202220565 CLASSIC-VIEW SERIES 5 REMOVE ALL PROTECTIVE TAPE FROM THE DOOR FRAME NOW. 13a Retainer Installation/Removal INSTALLATION Your door is shipped with the screen and glass inserts in the window opening. 2. Position screen sash below glass, with tilt barrels down and screen spline facing inside of door. NOTE: Operating insert has a ledge that extends from the bottom to aid in operation. 6 202220565 CLASSIC-VIEW SERIES 14 Install Screw Cap Covers Larson has 2 different types of screw covers. Cut screw cover to correct length if needed using a scissors or a tin snip. Starting at one end, snap the cover on working your way towards the other end. Cut the latch and hinge z-bar screw covers to length--matching the z-bar lengths respectively. Attach the latch and hinge z-bar screw covers as described in step #1. FIGURE 23 TOP Z-BAR (DRIP CAP) SCREW COVER VINYL SCREW COVER HINGE Z-BAR SHOWN HINGE Z-BAR *NOTE: Some models do NOT come with screw covers! DETAIL A INSTALLED POSITION LATCH Z-BAR FIGURE 24 TOP Z-BAR (DRIP CAP) SCREW COVER HINGE Z-BAR SHOWN PUSH ON VINYL SCREW COVER HINGE Z-BAR LATCH Z-BAR INSTALLED POSITION Larson Storm Door Warranties CLASSIC-VIEWTM Limited Lifetime Warranty During life of door, new door at no charge. Hardware warranty is 1 year, covering workmanship and mechanical parts (brass finish is not covered under the warranty). To maintain your brass finish, see the "General Care and Maintenance" section on page 10. HARDWARE 1-Year Warranty STORM DOOR WARRANTY LIMITATIONS: Modification of door will void warranty. Screen damage, glass breakage, or wind damage is not covered under warranty. In order to obtain performance under these warranties, the original owner shall do the following: 1. Send in the warranty registration card within 30 days following purchase. Notify authorized dealer of defect, with proof of purchase. 202220565 CLASSIC-VIEW SERIES 7 Classic-ViewTM Series Storm/Screen Doors CLOSER INSTRUCTIONS 1 FIGURE 25 Closer Installation CLOSER 1/4" NOTE: Be sure door opens and closes freely before installing the closer. Some models have two closers and others have one closer. "HOLD OPEN" WASHER EXTEND ROD 1/4" OUT FLANGE CLOSER ASSEMBLY PREPARATION 1. Pull rod out of closer so that there is a 1/4" gap per Figure 25 (insert small screwdriver in rod hole to provide pulling grip). Attach closer rod to side jamb bracket (short connecting pin) with open side of jamb bracket toward storm door (see arrow on bracket). Close and latch door. FIGURE 26 #10 X 1/2" SCREW #10 X 1 1/2" SCREW SHORT PIN LONG PIN INSTALLATION: ONE CLOSER MODELS 1. To install the closer, hold closer assembly 1-1/2" down from top of door and hold jamb bracket 1/4" back from storm door. [. . . ] Do not use abrasive cleaners or cloths as they may damage the clear coat finish. Apply non-abrasive paste wax on the brass hardware to help restore it's bright finish. · Refinishing (if clear coat is damaged and tarnishing has occurred) 1. This can be done by using a paint stripper, or by lightly rubbing the hardware using #0000 steel wool. [. . . ]