User manual LARSON CLASSIC ELEGANCESEAL

[. . . ] 202220564 LM 4/04 Classic-Seal/Classic-Elegance Storm Doors INSTALLATION INSTRUCTIONS Congratulations on your new storm door. If you need assistance or parts, please call our hotline or visit our website. READ BEFORE BEGINNING INSTALLATION TOP Z-BAR OR DRIP CAP CAUTION INSTALLATION QUESTIONS?PLEASE CALL 1-888-483-3768 OR VISIT www. larsondoors. com PINCH · Read instructions thoroughly · Use two people when lifting and installing the door. [. . . ] Tilt the glass sash to the left to remove the top tilt keys from the track sash. Reinstall by reversing the previous steps. 13B NO CIRCULATION VENTILATION VENTING TOP & BOTTOM VENTING TOP VENTING BOTTOM VENTING FIGURE 21 Note potential Pinch Points shown on Figures 19 & 20. Operating inserts should be operated slowly and with caution. CAUTION 202220564 CS/CE OVERLAP 5 TO REMOVE GLASS OR SCREEN Place sharp flat-nose screwdriver blade in groove next to door frame (approximately 1/2" from top or bottom of window) and (Full glass version) pry end of retainer loose. Screen REINSTALL RETAINERS Start one end of the retainer into the track at the top or bottom of the window and push retainer into the track as shown. Screen damage, glass breakage, or wind damage is not covered under warranty. In order to obtain performance under these warranties, the original owner shall do the following: 1. Send in the warranty registration card within 30 days following purchase; 2. Notify authorized dealer of defect, with proof of purchase. Note: Warranty applies to original owner only. Proof of purchase required. 6 CS/CE OVERLAP 202220564 Classic-Seal/Classic-Elegance Storm Doors CLOSER INSTRUCTIONS Closer Installation (Some models have two closers and others have one closer. ) 1. Pull rod out of closer so that there is a approximately 1/4" gap per Figure 1 (insert small screwdriver in rod hole to provide pulling grip). Closer Assembly Position washer behind flanges and against the closer. Attach front Be sure door opens hole in closer to door bracket (long connecting pin). Attach and closes freely closer rod to side jamb bracket (short connecting pin) with before installing the open side of jamb bracket toward storm door (see arrow on closer. Close and latch door. STEP 1 1/4" "HOLD OPEN" WASHER CLOSER FLANGE EXTEND ROD 1/4" OUT FIGURE 1 CLOSER INSTALLATION 1/4" FROM DOOR 1. To install the closer, hold closer assembly 1-1/2" above door window and hold jamb bracket 1/4" back from storm door. Closer Assembly Mark jamb bracket holes and two holes in door bracket. The open side of the jamb bracket should be toward the storm door (see arrow on bracket). Hold the closer and door bracket level and mark the location for the insertion of the door bracket screws. To hold the door open: open door and slide hold-open washer over flanges toward cylinder on closer. STEP 2A ONE-CLOSER MODELS DOOR BRACKET T O OP CH PIN OO FD R HINGE SIDE JAMB #10 x 1-1/2" SCREWS 1-1 /2" TOP CLOSER #10 x 5/8" SCREWS SHORT CONNECTING PIN LONG CONNECTING PIN SIDE JAMB BRACKET BOTTOM CLOSER /2" 1-1 PIN CH LOOKING AT DOOR FROM INSIDE 1. To install the top closer, hold closer assembly 1-1/2" above door window and hold jamb bracket 1/4" back from storm door. Closer Assembly Mark jamb bracket holes and two holes in door bracket. The open side of the jamb bracket should be toward the storm door (see arrow on bracket). [. . . ] Note: If refinishing keyed hardware, cover the key opening with masking tape to keep out stripper or steel wool particles. 3. Once the clear coat is removed, continue to lightly rub with #0000 steel wool over tarnished areas until the bright brass finish returns. The lacquer can be purchased at most hardware stores and should be applied per label directions. Note: If refinishing keyed hardware, cover the key opening with masking tape when applying the lacquer finish (protecting the locking mechanism from gumming up). [. . . ]