User manual LACIE P9221 QUICK INSTALL

[. . . ] Battery Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rack System Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The 12big Rack Storage Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Constant amber: the fan has a fault. 4. 4. 5. Rear Panel LED The rear panel LED (shown in Fig. 23) is used to identify the enclosure in the same way as the ID LED described in section 4. 4. 1. Ops Panel LEDs and Switches. LaCie 12big Rack Storage Server User Manual Operation page 23 4. 4. 6. 2. Refer to your ATX Server documentation for full details of the LED states. Table 10 - Network Port LEDs LED Left LED State Off Solid green Blinking green Description No network connection Network connection is active Transmit / receive activity is occurring 10 Mbps connection (if left LED is on or blinking) 100 Mbps connection 1000 Mbps connection Right Off Solid amber Solid green LaCie 12big Rack Storage Server User Manual The Management GUI page 24 5. Connecting to the Web Management Interface Before connecting to the management GUI, the baseboard management IP address needs to be confirmed. Go to Set LAN configuration menu, which is located under "System Management". Set LAN channel IP Address source, IP Address, MAC address, Subnet Mask and (if required) the Gateway address on the corresponding menu. The default user name and password are "admin" and "admin". Users will be logged out automatically after 300 seconds of inactivity. 5. 2. Information Once connected to the Web Management Interface, the first page seen is the System Information. All board information is displayed on this page. 5. 2. 2. Event Log On the left column, the Event Log section can be selected by clicking on the corresponding text. An Administrator can even execute configuration commands that will disable the channel that the Administrator is working on. All BMC commands are allowed, except for configuration settings which can change the behavior of the out-of-band interfaces. For example, Operator privilege does not allow the capability to disable individual channels or change user access privileges. Forbidden commands include those that can be used to alter BMC configuration, write data to the management controllers, or perform system actions such as resets, power on/off, and watchdog activation. If the upgrade is successful, the "Activate and Reboot Management" button will appear. This step only reboots the BMC, not the whole enclosure. Callback No Access User ID 1 is a user without a name or password. This user can be enabled or disabled and has a privilege level set to "User" by default. Users are automatically logged out after 300 seconds of inactivity. LaCie 12big Rack Storage Server User Manual BIOS Settings page 29 6. AMI BIOS Setup Program All relevant information for operating the board and connected peripherals are stored in the CMOS memory backed-up by a battery or in the main BIOS flash and EEPROM. 6. 1. 1. Accessing the BIOS Setup Utility The system BIOS (Basic Input Output System) provides an interface between the operating system and the hardware of the 12big Storage Server ATX board. It uses the AMI Setup program, a setup utility in flash memory that is accessed by pressing the <DEL> (or <F4> from a console redirection terminal) key at the appropriate time during system boot. To run the AMI Setup program incorporated in the ROM BIOS: Turn on or reboot the system. [. . . ] Initialize the CPU's before boot, which includes the programming of the MTRR's. This range is reserved for chipset vendors & system manufacturers. The error associated with this value may be different from one platform to the next. OEM PCI init debug POST code during DIMM init, See DIM Code Checkpoints section of document for more information. A8 A9 AA AB AC B1 0 61-70 50 52 60 75 78 7A 7C 84 85 87 8C 8D 8E 90 A0 A1 A2 DD-DE LaCie 12big Rack Storage Server User Manual POST page 78 13. 4. [. . . ]