User manual LACIE P9220 QUICK INSTALL

[. . . ] Replacing a Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fitting Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operator Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The unit must only be operated from a power supply input voltage range of 100-240 VAC, 50-60 Hz. The plug on the power supply cord is used as the main disconnect device. Ensure that the socket outlets are located near the equipment and are easily accessible. The power connection must always be disconnected prior to removal of a PSU module from the enclosure. A safe electrical earth connection must be provided to the power cord. Provide a suitable power source with electrical overload protection to meet the requirements laid down in the technical specification. This equipment is intended to operate with two working PSUs installed in the Power Supply Module. Before removal/replacement of a PSU disconnect all power for isolation. A faulty PSU must be replaced with a fully operational one within 24 hours. CAUTION: If this equipment is used in a manner not specified by LaCie, the protection provided by the equipment may be impaired. IMPORTANT INFO: The enclosure top cover must be secured, when the enclosure is in normal use, by rotating the lock 90° to the `locked' position. This is to prevent users/operators from accessing the service areas. 2. Before You Begin Before you begin, make sure the site where you intend to set up and use your enclosure has the following: Standard power from an independent source or a rack power distribution unit with a UPS. Figure 4a: Removing a PSU Figure 4b: Removing a PSU LaCie Quick Install Guide 5 3. 5. Replacing a Fan IMPORTANT INFO: The cover must only be opened by service personnel. Release the enclosure top cover by turning the lock mechanism to the `Unlocked' position and slide the cover back until it stops (see Figure 5). 3. Replace the Fan by pushing it all the way into the enclosure until it fits firmly and is level with the other Fans. Ensure that the Fan module LED extinguishes within 10 seconds of installation. Close the enclosure cover and secure by turning the lock mechanism to the `Locked' position. 3. 6. CAUTION: There is a danger of explosion if the battery is replaced by an incorrect type. Dispose of used batteries in accordance with the manufacturer's instructions and national regulations. CAUTION: The batteries on the NVRAM card(s) are not replaceable; the complete card assembly must be replaced in the event of battery failure. Therefore the complete card assembly must be replaced annually or in the event of battery failure. Figure 5: Removing the Enclosure Cover 2. Grip the faulty Fan module with finger and thumb and pull it upwards in order to unplug it, and remove it from the enclosure (see Figure 6). 3. 7. [. . . ] If you want to change something, click Back and change the configuration parameters. Otherwise, click Finish to accept the configuration and start the initialization process (unless you selected No Initialization above). 4. 4. To access your drive configuration, launch Server Manager from the Windows Start Menu and select Storage > Disk Management. Figure 16 - Create Drive Group 3. In the Virtual Disk Properties screen, modify default settings as follows in order to achieve best performance: a. [. . . ]