User manual LACIE BLUE EYE PRO PROOF EDITION

[. . . ] LaCie blue eye pro User Manual Table of Contents page 1 Table of Contents 1. Introduction to LaCie blue eye pro. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Your LaCie blue eye pro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Box Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Differences in percentage are also displayed This value represents the luminance of the black color displayed by the monitor. This table (d) summarizes the measurements taken of the greyscale displayed by your monitor. For each line, you will find: Color ­ the shade of gray measured Kelvin ­ the temperature of the measured color Chroma ­ the chromaticity difference between the measured color and target color Gamma ­ the Gamma value of the curve on which the point belongs Average Gamma (e) ­ the average of the values given in the Gamma table: This is the average of the values given in the gamma column. c a b d e LaCie blue eye pro User Manual This table (a in figure C) summarizes the L*a*b values of the measured color patches and their measured delta-E and Delta-E (CIE94) values. This table (b in figure C) summarizes the XYZ values of the measured color patches for the Black, White and 50% Gray color patches, and their measured Color Temperature. If you performed the UGRA Display Analysis and Certification version of test, the Report (figure D) is more detailed and contains the UGRA Certification level of the monitor as well as all relative measurements, including Gray Balance and UGRA/ FOGRA Mediawedge color patches, as well as Monitor Uniformity results. Calibrating LaCie 300/500/700 Series Monitors page 24 a b Fig. C Basics UGRA Display Analysis & Certification Tool Report 2008-7-16 9:25:59 v1. 3. 1 LaCie 724 LaCie 724 H1AK500000 /Library/ColorSync/Profiles/16. 07. 08-5000K-18-120cd. icc 2008-7-16 9:19 eye-one display 2 Date: Report-Version: Monitor-Name: EDID-Name: EDID-Serial: Profile: Created: Measurement device: Summary The monitor has passed the certification according to the UGRA DACT specifications. Calibration White Point Gray balance Profile quality yes yes yes Softproofing MultiColor, HighBody Offset/Gravure Paper Type 1/2 Offset on uncoated paper Newspaper Printing sRGB AdobeRGB ECI-RGB yes yes yes yes yes yes yes Diagram WhitePoint Gray Balance Profile Quality Softproof Quality Fig. D LaCie blue eye pro User Manual Calibrating LaCie 300/500/700 Series Monitors page 25 5. 4. Advanced Options This menu allows you to set up advanced calibration options used for special purposes (Fig. Optimize for Accuracy or for Speed Blue eye pro offers you the possibility to adjust the calibration process according to your preference for Accuracy or Speed. Checking the Speed option will reduce the number of color patches measured and the number of optimization rounds the software performs, and will shorten the calibration process by approximately 30%. Blackpoint Adjustment Setting You may elect to increase the luminance of the color black. This can be useful to obtain a realistic rendering of your document in situations where you know that the paper and inks used when ultimately printing it may not allow a full black. To increase the luminance of black, adjust the blackpoint slider to your desired value. This setting will be automatically taken into consideration when calibrating your monitor. 5. 4. 3. Chromatic Adaptation Setting Some constraints in your color chain may force you to use a monitor White Point other than D50 (5000° Kelvin) while still targeting D50 paper prints. In this situation, you may perceive a difference between displayed colors and printed colors, due to the Chromatic Adaptation behavior of the human brain. When one of these methods is selected, the profiling process of LaCie blue eye pro will minimize this impression by slightly adjusting the chromaticity of your monitor. To activate this feature, please select your chosen chromatic adaptation method by clicking on the corresponding radio button of the Advanced Options settings window. 5. 4. 4. Profile type With LaCie blue eye pro you can choose the type of profile you want to create. Select the required Profile type by clicking on the related but- LaCie blue eye pro User Manual ton. [. . . ] Yes, a saved profile can be loaded without having the colorimeter connected. No, the LaCie blue eye pro software is only compatible with Mac OS 10. 1 and later. No, simply select your previous profile from the Select Profile module. Yes, but you will need to use an ADC to DVI converter cable. Issues regarding the Select Profile Module. [. . . ]