User manual LACIE 2BIG NETWORK 2-DISK RAID

[. . . ] 2big network Professional 2disk RAID Gigabit Ethernet user manual manuel utilisateur manual de instrucciones gebruikershandleiding guída utente handbuch LaCie 2big Network User Manual Table of Contents page Table of Contents Health and Safety Precautions General Use Precautions 1. Editing Groups 4 4 6 6 7 8 9 10 11 11 12 13 14 15 16 17 19 20 20 21 22 23 24 25 25 26 26 27 28 28 29 29 29 30 30 31 32 32 LaCie 2big Network User Manual 3. 6. Warranty Information Table of Contents page 33 33 34 35 35 36 36 37 37 38 39 39 39 41 41 42 43 43 43 44 45 45 46 47 47 48 48 48 49 51 52 53 53 54 55 55 56 57 58 61 62 63 LaCie 2big Network User Manual Copyrights Copyright © 2007 LaCie. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of LaCie. [. . . ] Deleting Groups On the Groups page, check the box beside each group you want to delete and click Remove. ImpOrTANT INfO: Deleting a group does not delete the users within the group. Go to the Users page to delete user accounts. administration page Figure 3. 5. 3 3. 5. 4. Editing Groups The administrator can edit the details of a group's profile at any time by clicking on a group on the Groups page to view the group's profile. LaCie 2big Network User Manual administration page 3. 6. Shares Click on the Shares link in the navigation bar to open the Shares page. Use this page to create, edit and delete shares. Figure 3. 6 3. 6. 1. The description only appears to the administrator as part of the Share Profile on this page. TeChNICAl NOTe: The share name cannot contain any of the following characters: \ / [ ] : | < > + = ; , ?Select Disabled to create the share but make it inaccessible. Figure 3. 6. 1 (continued on next page) LaCie 2big Network User Manual 4. Select "Enable public access" to make the share accessible in read/write mode to anyone. Select "Enable guest access" to require a password for read/write access. You can choose from Windows , Apple (SMB), FTP or HTTP. administration page 3. 6. 2. Creating a Share from a USB Key To automatically create a share from a USB key, just connect the USB key to a USB port on the back of the 2big Network and push the big blue button on the front of the drive. The following things will happen: A new share will be created on the 2big (Fig. When you disconnect the USB key from the 2big the data will still be available because it has been copied to the 2big. NOTe: Shares created with 1-click data sharing (USB keys) are different from shares created by attaching exernal storage devices like USB hard drives. When a share is created by attaching a USB hard drive, the drive must be connected at all times for its data to be accessible. Shares created from USB keys with 1-click data sharing are created on the 2big and are always accessible. Figure 3. 6. 2 LaCie 2big Network User Manual 3. 6. 3. Deleting Shares On the Shares page, check the box beside each share you want to delete and click Remove. Deletion of the share could take just a few seconds to several minutes, depending on the size of the share. CAUTION: Deleting a share deletes all files contained within the share folder. Back up any data you want to save before deleting a share. administration page Figure 3. 6. 3 3. 6. 4. [. . . ] If your network is DHCP enabled, please refer to sections 2. 3, Connecting with LaCie Ethernet Agent or 2. 4, Connecting with the IP Configurator Wizard. If your network is not DHCP enabled, you will need to manually configure the address; please see section 2. 5, Configuring the 2big Network on a LAN Without a DHCP Server. If you are using AppleTalk under Mac OS 9. x, ensure that the LaCie 2big Network and the other clients on the network are in the same AppleTalk zone. Are you using AppleTalk under Mac OS 9. x? LaCie 2big Network User Manual Troubleshooting page 0 Problem A user does not have access to the LaCie 2big Network. Question to Ask Has the administrator created that specific user? Solution In order for a another user to access the LaCie 2big Network, two conditions must be met: 1) the administrator must create and register a user with the appropriate privileges; 2) the LaCie 2big Network must be connected to the network via Ethernet for additional users to access the drive. LaCie 2big Network User Manual Contacting Customer Support page 8. Contacting Customer Support Before You Contact Technical Support 1. [. . . ]