User manual LACIE 12BIG RACK NETWORK

[. . . ] LaCie 12big Rack Network User Manual Table of Contents page 1 Table of Contents 1. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 The LaCie 12big Rack Network System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 The Enclosure Core Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] CAUTION: The power connections must always be disconnected prior to removal of the Power Supply Unit from the enclosure. 2. 6. Module Installation IMPORTANT INFO: LaCie 12big Rack Network enclosures are supplied and delivered populated with Backplane PCB, ATX Motherboard, Enclosure Management PCB, SAS Expander PCB, Ops Panel, Intel® RAID Controller (optional), Battery Backup Unit (optional) and all plug-in modules installed. For information on removal/replacement of plug-in modules, please refer to 4. Troubleshooting & Problem Solving. CAUTION: Bifurcated power cords MUST NOT be used with the LaCie 12big Rack Network enclosure, this system does not support their use. LaCie 12big Rack Network User Manual Installation page 21 2. 8. Grounding Checks The product must only be connected to a power source that has a safety electrical earth connection. CAUTION: If more than one product is fitted in a rack, the earth connection to the rack is even more important, because the rack will then have a high "EARTH LEAKAGE CURRENT" ("TOUCH CURRENT"). The earth connection to the rack must be checked before switching on, by an electrical engineer who is qualified to the appropriate local and National standards to perform the check. 2. 9. Data Security Power down your host computer and all attached peripheral devices before beginning installation. Handle them with care, and keep them away from strong magnetic fields. All the supplied plug-in modules and blanking plates must be in place for the air to flow correctly around the enclosure and also to complete the internal circuitry. If the subsystem is used with modules or blanking plates missing for more than a few minutes, the enclosure can overheat, causing power failure and data loss. If it is faulty, replace it with a drive module of the same type and capacity. Ensure that all disk drives are removed from the enclosure before attempting to manhandle or move the rack installation. CAUTION: Prior to removing the PSU from the Power Supply Mounting Cage in the enclosure: Please disconnect the power from the power supply, by either the mains switch (where present) or by physically removing the power source, to ensure your system has warning of an imminent power shutdown. LaCie 12big Rack Network User Manual Operation page 22 3. Before You Begin Before powering up the enclosure please ensure that all the modules are firmly seated in their correct bays. 3. 2. Power On CAUTION: Do not operate the subsystem until the ambient temperature is within the specified operating range. If the drives have been recently installed ensure they have had time to acclimatize before operating them. Fig. 14 - Enclosure Rear View showing Switches and Connections NOTE: Please refer to Fig. The Power Active LED on the Ops Panel should be lit (Green) when the enclosure power button is pressed (and the disk drive motors should start). IMPORTANT INFO: If mains power is lost for any reason, on restoration of power the enclosure will re-start automatically. 3. 2. 1. Power Supply Unit LEDs The PSU incorporates a bi-color Red/Green LED. When the PSU is connected to a mains supply the Green LED will flash. When the PSU is switched on the Green LED will be continuously illuminated. [. . . ] NEMA 5-15P grounding-type attachment plug rated 120V 10A; or IEC 320 C14, 250V, 10A. Europe & Others General requirements:Cord type Socket Harmonized, H05-VVF-3G1. 0 IEC 320, C-13, 250V, 10A. IMPORTANT INFO: The Plug and the complete power cord assembly must meet the standards appropriate to the country, and must have safety approvals acceptable in that country. LaCie 12big Rack Network User Manual Rack Kit Reference Drawing page 52 8. 38 shows the ATX Reduced Rail Kit drawing which is included with the Rack Mounting Rail Kit and provides rail assembly details. Please contact LaCie for the latest issue of this drawing. continued on the next page >> A 01-A NH 25440 B C FIGURE 1 CLAMPING SCREWS LaCie 12big Rack Network User Manual D Fig. [. . . ]