User manual LACIE 12BIG RACK FIBRE 8 DUAL

[. . . ] LaCie 12big Rack Fibre 8 User Manual Table of Contents page 1 Table of Contents 1. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LaCie 12big Rack Fibre 8 Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12big Rack Fibre Expansion Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A host computer with a standard FC HBA (host bus adaptor) with the appropriate BIOS and drivers. Refer to the instructions provided with your HBA to install and its driver software. IMPORTANT INFO: For Microsoft Windows Servers - Insert the Software and Manuals Disc, click the Pseudo LUN Driver (INF) button and follow the on-screen installation instructions. 2. 3. 2. Unpacking the Storage System The package contents and unpacking procedure are illustrated in Fig. IMPORTANT INFO: The Accessory Box contains the AC power cord(s), anti-tamper lock key, host interface cables, expansion cables, RS232 cable, the Software and Manuals disc, and the rails and hardware parts for rack mounting. continued on the next page>> LaCie 12big Rack Fibre 8 User Manual System Overview page 26 Initial Unpacking Steps 1. Inspect the packaging for crushes, cuts, water damage, or any other evidence of mishandling during transit. If any damage appears to be present, it is suggested to take photographs of the packaging before opening any boxes. You may want to contact the shipping company if there is apparent damage. Remove the protective plastic wrapping and inspect for any obvious damage. It is advisable to remove the Power Cooling Modules and the top row of Disk Drives before lifting the enclosure from the carton. Module Removal & Installation for instructions to remove and re-install the plug-in modules. Remove the lower rows of disk drives and RAID Controllers or Disk I/O Modules in preparation for rack installation. IMPORTANT INFO: You may wish to save your packaging materials in the event it becomes necessary to ship the storage system. 2. 3. 3. Rack Installation Procedure 2. 3. 3. 1. Rack Installation Pre-Requisites The LaCie 12big Rack Fibre 8 and 12big Rack Fibre Expansion enclosures are designed for installation into an industry standard 19inch cabinet. Weight: up to 27 kg (59 lb. ) dependent upon configuration per enclosure. A minimum gap of 25 mm (1 inch) clearance between the rack door and front of the enclosure; and 50 mm (2 inches) rear clearance between rear of the enclosure and rear of the rack is recommended in order to maintain the correct air flow. The rack should present a maximum back pressure of 5 pascals (0. 5 mm water gauge). A pascal count of 5 or greater can restrict airflow and could cause cooling problems. LaCie 12big Rack Fibre 8 User Manual System Overview page 27 2. 3. 3. 2. Rack Mounting Rail Kit A set of mounting rails is provided for use in 19-inch rack cabinets. These rails have been designed and tested to handle the maximum enclosure weight and to ensure that multiple 12big Rack Fibre enclosures may be installed without loss of space within the rack. Use of other mounting hardware may cause some loss of rack space or damage to the equipment. 2. 3. 3. 3. With the empty enclosure chassis on a stable work surface, attach the left and right chassis slides to the enclosure sides using a total of 10 M3 x 4 button head screws (see Fig. The front portion of the chassis slide has two tangs which insert into holes on the forward edge of the enclosure side panel. Assemble the left and right chassis latches using the chassis latch screws. [. . . ] AC Power Cords IMPORTANT INFO: The plug and the complete power cord assembly must meet the standards appropriate to the country, and must have safety approvals acceptable in that country. United States (Must be NRTL Listed (National Recognized Test Laboratory, e. g. UL)) Cord Type SV or SVT, 18 AWG minimum, 3 conductor - 4. 5 meters maximum length. NEMA 5-15P grounding-type attachment plug rated 120V 10A; or IEC 320 C14, 250V, 10A. IEC 320 C-13, 250V, 10A. Plug Socket Europe and Others Cord Type Socket Harmonized, H05-VVF-3G1. 0. [. . . ]