User manual LACIE 12BIG RACK SERIAL

[. . . ] LaCie 12big Rack Serial User Manual Table of Contents page 1 Table of Contents 1. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LaCie 12big Rack Serial SAS Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The Enclosure Core Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Rack Mounting Rail Kit A set of mounting rails is available for use in 19 inch rack cabinets (Fig. These rails have been designed and tested to handle the maximum enclosure weight and to ensure that multiple LaCie 12big Rack Serial may be installed without loss of space within the rack. The rack mounting rail kit also incorporates a rear hold down mechanism to ensure shock and vibration immunity. Please contact your supplier to ensure suitable mount rails are available for the rack you are using. LaCie 12big Rack Serial User Manual Installation page 18 2. 4. 3. Rack Installation Procedure Please refer to the detail drawings supplied with the rack mounting rail kit for further information 2. 4. 3. 1. Remove the Rack Mounting Kit from the Accessories Box and check for damage. Attach left and right chassis slides to the enclosure sides using 8 M3 x 4 button head screws (see Fig. Assemble the left and right chassis latches using the special chassis latch screws. 18, with the spring arm located against its stop. On the right hand this is at the top, on the left it is at the bottom. Assemble the left and right chassis latches using the special chassis latch screws. On the right hand side this is at the top, on the left at the bottom. Fig. 18 - Securing Chassis Slides to Enclosure (steps 1 & 2) continued on the next page >> LaCie 12big Rack Serial User Manual Installation page 19 Assemble the rack brackets to the rack posts as follows (see Fig. Locate the location pin at the rear of the rail into a rear rail post hole. Attach the bracket to the rear rack post using the washers and screws supplied. Attach the bracket to the front rack post using the washers and screws supplied. Tighten the two clamping screws located along the inside of the rear section of the rack bracket (see Fig. Carefully insert the chassis slides into the rack rails and push fully home. Withdraw the enclosure until it reaches the hard stops (approximately 400mm, 16. 75 inches) and tighten the front rack bracket mounting screws. Return the enclosure to the fully home position and attach to the rack using the captive fasteners on the front flanges. Fig. 19 - Rack Mounting Rail Kit 2. 4. 4. Chassis Installation 2. 4. 4. 1. Parts Check List Chassis (complete with Backplane, Ops Panel and all plug-in modules installed). Fit the Rack Mounting Rail Kit in accordance with the mounting kit Installation procedure. Slide the chassis assembly onto the rack rails until the front flanges engage on the rack. [. . . ] Unauthorized changes or modifications could void the user's authority to operate the equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. LaCie 12big Rack Serial User Manual Standards & Regulations page 51 7. 3. European Regulations This equipment complies with European Regulations EN 55022 Class A: Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology Equipments and EN50082-1: Generic Immunity. 7. 5. 2. Europe & Others General requirements:- Table 25 - Europe & Others Power Cord Compliance Cord Type Socket Harmonized, H05-VVF-3G1. 0 IEC 320, C-13, 250V, 10A. 7. 4. PSU Safety and EMC Compliance Table 23 - PSU Safety and EMC Compliance Safety Compliance UL 60950 IEC 60950 EN 60950 IMPORTANT INFO: The Plug and the complete power cord assembly must meet the standards appropriate to the country, and must have safety approvals acceptable in that country. 7. 6. [. . . ]