User manual LA CROSSE TECHNOLOGY WT-8008U

[. . . ] Once you have started the configuration, you will be able to move from one step to another by pressing the "SET" button. If at any point during the setup process you need to start over, avoid pressing any buttons for roughly 30 seconds or wait until the display stops flashing, then repeat the steps outlined in this section. Note: The following steps often refer to two buttons: "+" and "- / °F/°C". The "+" button is used to increase setting values and the "-/ °F/°C" button is used to decrease setting values. [. . . ] The display is now flashing "12 Hr" and you are ready to begin configuring your clock. Set 12 or 24 Hour Time Mode With the display flashing "12 Hr", press the "+" or "- / °F/°C" button to select either a 12 or 24 hour time mode. Set Time - Hour Once you have chosen 12 or 24 hr time mode, press the "SET" button again and the Hour digits will begin to flash. Use the "+" and "- / °F/°C" buttons to select the correct hour. Set Time - Minute Once the hour is set, press the "SET" button again and the Minutes digits will flash. Use the "+" and "- / °F/°C" buttons to select the correct minute. Set Date ­ Year Once the minute is set, press the "SET" button again and the Year digits will flash. Use the "+" and "- / °F/°C" buttons to select the correct year. To Set the Time Alarm 1. To set the Alarm Time - Hour: Press and hold down the "ALM" button for 3 seconds until the hours digits flash. Press the "ALM" button to confirm your setting and move to setting the minutes. To set the Alarm Time - Minutes: The Minutes digits of the Alarm Time will flash. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new Care and Maintenance Extreme temperatures, vibration and shock should be avoided as these may cause damage to the unit and give inaccurate readings. Injuries, burns, or property damage may be resulted if batteries are in contact with conducting materials, heat, corrosive materials or explosives. Batteries should be taken out of the unit before it is stored for a long period of time. Page 5 of 8 Page 6 of 8 or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. [. . . ] The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your owner's manual; (5) damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference. . This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal setup or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installationrelated circumstances. [. . . ]