User manual LA CROSSE TECHNOLOGY WT-3145U

[. . . ] Please Note: WWVB time will over ride a manual setting. For more information on the NIST and radio controlled time, see www. boulder. nist. gov/timefreq/ Insert 1 new AA, LR6 1. 5 volt ALKALINE battery in the analog clock battery compartment according to the polarity marked on the case, then 1 new battery AA, LR6 1. 5 V into the digital clock. Once the battery is installed, the clock will begin searching for a signal. For the initial setting, it is recommended to stand the clock in an upright position near a window. Within 3 - 10 minutes the clock will either receive the WWVB signal and set itself to the exact time (for the default Pacific Time Zone), or it will determine that the signal is not receivable at its current location and time of day. [. . . ] The changeover from standard time to daylight saving time, and vice versa, takes place automatically with the same precision. MANUAL TIME SET BUTTON 1. Press and hold the Manual Set button until the second hand of the clock moves to the 12 position. Release the Manual Set button and again press and hold the Manual Set button. About 3 seconds later, the second hands will start to move and the clock is now running with manual time. Press time zone button to select a time zone after the clock received the WWVB signal. If you are in the Pacific Time Zone- you are ready to hang your clock. If you are not in the Pacific Time Zone, select your time zone by press and holding for 5 second, one of the four time zone buttons PT-Pacific Time, MT-Mountain Time, CT-Central Time, ET-Eastern Time. If multiple buttons are pressed, the clock will set to the time zone selected last. If you live in an area that does not recognize DST (Arizona) you must press the (unmarked) DST button for one second to deactivate your clock's DST program. For time zones outside of PT, MT, CT or ET you must manually set the time using the Manual Time set button on the back of the movement. Please Note: WWVB time will over ride a manual setting. ADDITIONAL DETAILS To set up your clock simply install one new AA, LR6 ALKALINE battery. Due to the nature of long wave radio signals it is normally not possible to receive a signal during the day so it is best to install the battery late in the evening. After the clock sets itself to Pacific Time, select your time zone by pressing one of the four time zone buttons PT-Pacific Time, MT-Mountain Time, CT-Central Time, ET-Eastern Time. Your clock can only set itself to 5. 6. Note: When the clock displays manual time, it will continue to try to receive the WWVB signal at each of the even numbered hours: 0:00, 2:00, 4:00, 6:00 . . . Remove the battery cover at the back of the clock and insert 1 AA Alkaline battery in the battery compartment. All segments of the LCD will light up briefly, then the display "-:--" and the current indoor temperature will be displayed. Note: If the Display time is pressed while the analog clock is still searching for the WWVB signal, the digital clock will display "--/--" for the date and "-:-" for the world time. Wait for the digital clock to receive the WWVB time and date from the analog clock. Then the digital clock will start normal runs. BATTERY COMPARTMENT COVER DISPLAY KEY TIME SET KEY (FOR WORLD TIME) BATTERY COMPARTMENT Month & day / Indoor temperature Month & day / Weekday 3. and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. [. . . ] To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. [. . . ]