User manual LA CROSSE TECHNOLOGY WT-3126H

[. . . ] Set the clock to your time zone by moving the indicator arrow to appropriate zone: P (UTC-8 Pacific Time), M (UTC-7 Mountain Time), C (UTC-6 Central Time), E (UTC-5 Eastern Time) Enable the Daylight Savings Time Auto Adjust feature by moving the DST switch to "ON". If you are in a time zone that does not follow DST, make sure you set the DST mode to "OFF". The Daylight Savings Time feature is disabled when the switch is set to "OFF". Insert 1 new AA, LR6 1. 5 volt ALKALINE battery in the analog clock battery compartment according to the polarity marked on the case. [. . . ] Once the clock is in manual mode, there Reset: If the clock does not respond to the various function modes, you can reset the clock by pressing the RESET button on the movement case. Internal Synchronization: Once the clock has been set correctly by the radio signal, the clock's CPU operates continuously. To ensure accuracy, the clock synchronizes the position of the second and minute hands to the time calculated by the CPU every day. and minute hand synchronization occurs between 1:50 and 2:01 am every day. Signal Interference: In some cases, the signal can be affected by weather conditions and electrical interferences, or the location of the clock itself may result in poor reception. If the clock has not synchronized to the correct time within a few days of activation, you may wish to move the clock to a different location. Try to place it near an outside wall closest to the direction of Colorado. Avoid placing the clock near electrical items such as TVs, microwave ovens and computers. Do not submerge clock in water. Extreme temperatures, vibration, and shock should be avoided to prevent damage to the clock. The WWVB time signal will easily penetrate masonry and wood framed buildings. The WWVB signal will penetrate almost every residential building and most steel buildings if they have adequate windows. It is not possible, however, for the WWVB signal to penetrate most indoor shopping malls and rooms in the center of large office buildings that do not have windows. In buildings that WWVB cannot penetrate you may set the time using the manual time set button. When the clock receives the WWVB signal it will automatically set the hands to the exact time. La Crosse Technology atomic clocks do not receive or process radio controlled time signals from Germany's DCF 77, Japan's J Ga AS, or England's MSFs atomically regulated transmitters. La Crosse Technology atomic clocks can be manually set and used anywhere. For more information on the NIST and radio controlled time, see www. boulder. nist. gov/timefreq/ SET BUTTON WAVE BUTTON RESET BUTTON BATTERY COMPARTMENT TIME ZONE SWITCH DST ON/OFF BUTTON DAYLIGHT SAVING TIME The National Institute of Standards and Technology and WWVB encode a special DST "bit" in the WWVB transmission for DST. Your La Crosse Technology clock will read this information and automatically advance the hands one hour in the spring and eleven hours in the fall. WARRANTY La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. [. . . ] This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. [. . . ]