User manual LA CROSSE TECHNOLOGY WS9125ITCA

[. . . ] If this does not happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1. In order to ensure sufficient 915 MHz transmission however, there should be a distance of no more than 330 feet between the final position of the Temperature Station and the sensor (see notes on "Positioning" and "915 MHz Reception"). 8 Using Multiple Sensors with One Temperature Station 1. User shall remove all the batteries from the Temperature Station and sensors and wait 60 seconds if setting has been done with one sensor before. Within 30 seconds of powering up the first sensor, insert the batteries to the Temperature Station. [. . . ] Return used batteries to an authorized depot. FUNCTION KEYS Temperature Station: The Temperature Station has two easy to use function keys. 16 SET/ CH key MIN/ MAX/ + key SET/CH key (Setting/Channel) · Press and hold for about 3 seconds to toggle between the temperature units (°F) or (°C). 17 · Press shortly to toggle between different channel readings. MIN/MAX/+ key (Min/ Max temperature) · Use to toggle between the minimum and maximum recorded readings of indoor & outdoor temperature. · Press and hold to reset minimum and maximum record (when min or max record is shown). 18 LCD SCREEN AND SETTINGS: Indoor Temperature in °F Receiver Low battery indicator Outdoor Channel No. Transmitter Low battery indicator Outdoor Temperature in °F Outdoor Reception Signal icon* 19 * When the signal from the sensor is successfully received by the Temperature Station, this icon will be switched on. User can therefore easily see whether the last reception was successful ("ON" icon) or not ("OFF" icon). On the other hand, the short blinking of the icon shows that a reception is being done at that time. For a better display clarity, the LCD screen is split into 2 sections, showing the indoor and outdoor temperatures. Section 1 - INDOOR TEMPERATURE · Display of indoor temperature. 20 Section 2 - OUTDOOR TEMPERATURE · Display of outdoor temperature. MANUAL SETTING: TEMPERATURE UNIT (°F) OR (°C) · User may choose to display the temperature readings in the unit of degree Fahrenheit (°F) or Celsius (°C). By pressing and holding the SET/CH key for about 3 seconds, the temperature unit of the displayed readings will shift between (°F) and (°C). 21 VIEWING THE MINIMUM AND MAXIMUM READINGS: User may consult the minimum and maximum recordings for indoor temperature, and outdoor temperature by following these steps: 1. Press the "MIN/MAX/+" key once to view the minimum indoor temperature and minimum outdoor temperature. Minimum icon 22 2. Press the "MIN/MAX/+" key once more to view the maximum indoor temperature and maximum outdoor temperature. Maximum icon Outdoor Channel No. 23 RESETTING THE MINIMUM AND MAXIMUM READINGS: User may reset the minimum and maximum temperature data to the current value by the following steps: 1. Press and hold the "MIN/MAX/+" key for about 3 seconds to reset all the minimum / maximum data to the current values in a single action. Data of all outdoor and indoor sensors will be reset at the same time. 24 TEMPERATURE SENSOR: The outdoor temperature is measured and transmitted to the Temperature Station approximately every 16 seconds. The range of the temperature sensor may be affected by the temperature. Please bear this in mind when placing the sensor. 915 MHz RECEPTION CHECK The Temperature Station should receive the outdoor temperature data within a few minutes after setup. If the temperature data are not received about 3 minutes after setup (the signal reception icon does not appear), or in normal display "---" is shown, please check the following points: 25 1. 4. The distance of the Temperature Station or sensor should be at least 5 to 6. 5 feet (1. 5 to 2 meters) away from any interfering sources such as computer monitors or TV sets. Avoid positioning the Temperature Station onto or in the immediate proximity of metal window frames. Using other electrical products such as headphones or speakers operating on the same signal frequency (915MHz) may prevent correct signal transmission and reception. Neighbors using electrical devices operating on the 915MHz signal frequency can also cause interference. Note: If the signal reception is not successful on the first frequency (915MHz) 26 for 45 seconds, the frequency is changed to 920MHz and the learning is tried another 45 seconds. If still not successful the reception is tried for 45 seconds on 910MHz. When the 915MHz signal is received correctly, do not re-open the battery cover of either the sensor or the Temperature Station, as the batteries may spring free from the contacts and force a false reset. If this happens accidentally, all units must be reset (see Setting up above) otherwise transmission problems may occur. However, this depends on the surrounding environment and interference levels. [. . . ] LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. KEEP OUT OF CHILDREN'S REACH. 41 This warranty gives you specific legal rights. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. [. . . ]