User manual LA CROSSE TECHNOLOGY WS9090

[. . . ] The outdoor temperature and the signal reception icon should then be displayed on the Temperature station. If this does not happen 3. 25 4. 5. after 3 minutes, the batteries will need to be removed from both units and reset from step 1. In order to ensure sufficient 868 MHz transmission however, this should under good conditions be a distance no more than 100 meters between the final position of the Temperature station and the transmitter (see notes on "Mounting" and "868 MHz Reception"). Once the remote temperature has been received and displayed on the Temperature station, the DCF time (radio controlled time) code reception is automatically started. [. . . ] When the time code is received, the DCF tower becomes permanently lit and the time will be displayed. If the tower icon flashes, but does not set the time or the DCF tower does not appear at all, then please take note of the following: · Recommended distance to any interfering sources like computer monitors or TV sets is a minimum of 1. 5 - 2 meters. · Within ferro-concrete rooms (basements, superstructures), the received signal is naturally weakened. In extreme cases, please place the unit close to a window and/ or point its front or back towards the Frankfurt transmitter. 30 · During nighttime, the atmospheric disturbances are usually less severe and reception is possible in most cases. A single daily reception is adequate to keep the accuracy deviation below 1 second. MANUAL SETTING The following manual settings can be done in the setting mode: · Manual time · Calendar · 12/24 hour time display · Time zone · Time reception ON/OFF (DCF ON/OFF) · Temperature unit ° F setting C/° Press and hold the SET key for about 3 seconds to advance to the setting mode: MANUAL TIME SETTING In area where reception of the DCF-77 time is not possible, the time can be manually set. Once the DCF signal is detected, it will change the manually set time into the received time. Please proceed the following setting steps at the first time before using the Temperature Station. Hours (flashing) Minutes (flashing) 1. Press again the SET key to confirm and enter the Calendar setting mode. Note: The unit will still try and receive the signal despite it being manually set. When it does receive the signal, it will change the manually set time into the received time. CALENDAR SETTING The date default of the Temperature station is 1. Once the radiocontrolled time signals are received, the date is automatically updated. However, if the signals are not received, the date can also be set manually: Year (flashing) Day (flashing) Month (flashing) 1. Press the SET key to enter the month (the month digit will be flashing). 5. Press the SET key to enter the weekday (the weekday digit will be flashing). Press the SET key to confirm and enter the 12/24 hour time display mode. GB MONDAY TUESDAY WEDNESDAY THURSDAY FRIDAY SATURDAY SUNDAY IT LUNEDÌ MARTEDÌ MERCOLEDÌ GIOVEDÌ VENERDÌ SABATO DOMENICA FR LUNDI MARDI MERCREDI JEUDI VENDREDI SAMEDI DIMANCHE DE MONTAG DIENSTAG MITTWOCH DONNERSTAG FREITAG SAMSTAG SONNTAG NL MAANDAG DINSDAG WOENSDAG DONDERDAG VRIJDAG ZATERDAG ZONDAG MONTAG - MON DIENSTAG - DIE MITTWOCH - MIT DONNERSTAG - DON FREITAG - FRE SAMSTAG - SAM SONNTAG - SON MONTAG - MON DIENSTAG - DIE MITTWOCH - MIT DONNERSTAG - DON FREITAG - FRE SAMSTAG - SAM SONNTAG - SON SP EL LUNES EL MARTES EL MIÉRCOLES EL JUEVES EL VIERNES EL SÁBADO EL DOMINGO 12/24 HOUR TIME DISPLAY SETTING To set the time format to 12h or 24h display mode (default 24h): Flashing 33 1. 2. Use the MIN/MAX/+ key to select the "12h" or "24h" display mode. Press the SET to confirm and to enter the Time zone setting mode. Note: When 24h mode display is selected, the calendar format will be "Weekday. When 12h mode display is selected, the calendar format will be "Weekday. Day" display. TIME ZONE SETTING The time zone can be set between ±12 hours (default 0 hour): Time zone (flashing) 1. Press the SET key to confirm and enter the Time reception ON/OFF setting mode. TIME RECEPTION ON/OFF SETTING In area where reception of the radio-controlled time (DCF time) is not possible, the time reception function can be turned OFF. Use the MIN/MAX/+ key to turn OFF the time reception function if necessary. C/° Confirm with the SET key and enter the ° F Temperature unit setting mode. Note: If the Time Reception function is turned OFF manually, the clock will not attempt any reception of the radio-controlled time (DCF time) as long as the Time Reception OFF function is activated. [. . . ] User shall take an active part in the reuse, recycling and recovery of the electrical and electronic waste. The unrestricted disposal of electronic waste may do harm on public health and the quality of environment. As stated on the gift box and labeled on the product, reading the "User manual" is highly recommended for the benefit of the user. This product must however not be thrown in general rubbish collection points. [. . . ]