User manual LA CROSSE TECHNOLOGY WS-9782TWC-IT

[. . . ] If this does not happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1. In order to ensure sufficient 915 MHz transmission however, this should under good conditions be a distance no more than 200 feet (60 meters) between the final position of the Temperature Station and the transmitter (see notes on "Positioning" and "915 MHz Reception"). HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION SETTING UP: Note: this temperature station can only receive one transmitter. First, insert the batteries to the transmitter (see "How to install and replace batteries in the Temperature transmitter" below). When batteries will need to be replaced, the low battery icon will appear on the LCD. [. . . ] 3. Press and hold the SET key in the normal display for about 3 seconds, the digit "F" will be flashing. Confirm by pressing the SET key to enter the 12/24 hour time display setting. MANUAL TIME SETTING To manually set the time of the Temperature Station: Hour (flashing) Minutes (flashing) Note: If no buttons are pressed within approximately 8 seconds while in any setting option, the unit will return to normal operating mode. 1. 3. 12 / 24- HOUR TIME DISPLAY SETTING The time format can be set in 12-hour or 24-hour mode (default setting "12"): The hour digit of the time display will be flashing. Press the + key to adjust the hour (press and hold to allow fast advance). Press the + key to adjust the minute (press and hold to allow fast advance). Press SET key once more to return to normal display. Flashing Note: If no buttons are pressed within approximately 8 seconds while in any setting option, the unit will return to normal operating mode. 12 11 VIEWING THE INDOOR TEMPERATURE The indoor temperature is displayed in the second section of the LCD: TO RESET THE MIN/MAX OUTDOOR DATA: The MIN/MAX outdoor temperature can be reset manually by pressing and holding the + key for about 3 seconds. This will reset the MIN/MAX temperatures to current outdoor temperature. Indoor temperature WEATHER GIRL ICON (Temperature condition icons): One of the 5 different temperature icons (featured by weather girl with different clothing) is displayed in the right side of the LCD, which indicates the different temperature conditions due to the current outdoor temperature: >78. 8F 66. 2 - 78. 7 F 50 - 66. 1F 32 ­ 49. 9F < 32F VIEWING THE OUTDOOR TEMPERATURE AND MIN/MAX TEMPERATURE The outdoor temperature is displayed in the last section of the LCD and the MIN/MAX outdoor temperature is displayed below the outdoor temperature. Outdoor temperature MIN outdoor temperature MAX outdoor temperature Note: The minimum/maximum temperature resolution is 0. 5°F / 0. 5°C. 13 14 915 MHz RECEPTION CHECK The Temperature Station should receive the outdoor temperature data within a few minutes after setup. If the temperature data are not received about 2 minutes after setup (the signal reception icon does not appear), please check the following points: 1. The distance of the Temperature Station or transmitter should be at least 5 to 6. 5 feet (1. 5 to 2 meters) away from any interfering sources such as computer monitors or TV sets. Avoid positioning the Temperature Station onto or in the immediate proximity of metal window frames. Using other electrical products such as headphones or speakers operating on the same signal frequency (915MHz) may prevent correct signal transmission and reception. Neighbors using electrical devices operating on the 915MHz signal frequency can also cause interference. Note: When the 915MHz signal is received correctly, do not re-open the battery cover of either the transmitter or the Temperature Station, as the batteries may spring free from the contacts and force a false reset. If this happens accidentally, all units must be reset (see Setting up above) otherwise transmission problems may occur. The transmission range is about 200 feet/ 60 m from the transmitter to the Temperature Station (in open space). However, this depends on the surrounding environment and interference levels. If no reception is possible despite the observation of these factors, all system units have to be reset (see Setting up above). POSITIONING THE TEMPERATURE STATION: The Temperature Station comes attached with a table stand, which provides the option of table standing the unit in addition to wall mounting. Before wall mounting, please check that the outdoor temperature values can be received from the desired locations. To wall mount: 1. Fix a screw (not supplied) into the desired wall, leaving the head extended out by about 5mm. Remember to ensure that it locks into place before releasing. 15 16 POSITIONING THE REMOTE TEMPERATURE TRANSMITTER: The remote temperature transmitter can be placed onto any flat surface or wall mounted using the bracket which doubles as a stand or wall mount base. in place, please ensure that the Temperature Station can receive the 915MHz signal from the temperature transmitter at the positions that you wish to place them. CARE AND MAINTENANCE: To wall mount: 1. Secure the bracket onto a desired wall using the screws and plastic anchors. [. . . ] LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information contact: La Crosse Technology, Ltd 2809 Losey Blvd. [. . . ]