User manual LA CROSSE TECHNOLOGY WS-9245UBK-IT

[. . . ] If this does not happen after 2 minutes, remove the batteries from both units and start again from step 1. In order to ensure sufficient 915 MHz transmission, the outdoor transmitter should be placed a distance of no more than 200 feet from the Temperature Station and the transmitter (see notes on "Positioning" and "915 MHz Reception"). HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION The Temperature Station uses 2 x AA, IEC LR6 1. 5V batteries. When batteries will need to be replaced, the low battery icon will appear on the LCD. To install and replace the batteries, please follow the steps below: 1. [. . . ] Press SET key once more to return to normal display. Note: If no buttons are pressed within approximately 8 seconds while in setting mode, the unit will return to normal operating mode. VIEWING THE INDOOR TEMPERATURE AND MIN/MAX The indoor temperature is displayed in the second section of the LCD along with the indoor MIN/MAX records: VIEWING THE OUTDOOR TEMPERATURE AND THE MIN/ MAX The outdoor temperature is displayed in the last section of the LCD along with the outdoor MIN/MAX records: Indoor temperature MIN indoor temperature MAX indoor temperature Outdoor temperature MIN outdoor temperature MAX outdoor temperature Notes: The maximum temperature record for the MIN indoor temperature can only be up to 10ºC, and the MIN/MAX temperature resolution is 1°C. The resolution of the indoor temperature is 0. 5ºC Notes: The minimum/maximum temperature resolution is 1°F. The resolution of the outdoor temperature is 0. 2ºF TO RESET THE MIN/MAX DATA: The MIN/MAX temperature can be reset manually by pressing and holding the + key for about 3 seconds. This will reset all indoor and outdoor MIN/MAX temperature to current indoor and outdoor temperatures. Using other electrical products such as headphones or speakers operating on the same signal frequency (915MHz) may prevent correct signal transmission and reception. Neighbors using electrical devices operating on the 915MHz signal frequency can also cause interference. LOW BATTERY INDICATOR Low battery indicator is displayed on the LCD when the batteries require changing. 915 MHz RECEPTION CHECK The Temperature Station should receive the outdoor temperature data within a few minutes after setup. If the temperature data are not received about 2 minutes after setup (the signal reception icon does not appear), please check the following points: 1. The distance of the Temperature Station or transmitter should be at least 1. 5 to 2 meters away from any interfering sources such as computer monitors or TV sets. Avoid positioning the Temperature Station onto or in the immediate proximity of Note: When the 915MHz signal is received correctly, do not re-open the battery cover of either the transmitter or the Temperature Station, as the batteries may spring free from the contacts and force a false reset. If this happens accidentally, all units must be reset (see Setting up above) otherwise transmission problems may occur. However, this depends on the surrounding environment and interference levels. If no reception is possible despite the observation of these factors, all system units have to be reset (see Setting up above). POSITIONING THE TEMPERATURE STATION: Table standing The Temperature Station comes attached with a table stand, which provides the option of table standing the unit in addition to wall mounting. POSITIONING THE REMOTE TEMPERATURE TRANSMITTER: The remote temperature transmitter can be placed onto any flat surface or wall mounted using the bracket which doubles as a stand or wall mount base. To wall mount: Before wall mounting, please check that the outdoor temperature values can be received from the desired locations: 1. Fix a screw (not supplied) into the desired wall, leaving the head extended out by about 5mm. Remember to ensure that it locks into place before releasing. To wall mount: 1. Secure the bracket onto a desired wall using the screws and plastic anchors. If, for instance, the unit is attached to a piece of metal, it may then either reduce or increase the transmitting range. For this reason, we recommend not to place the unit on any metal surfaces or in any position where a large metal or highly polished surface is in the immediate vicinity (garage doors, double glazing, etc. ). Before securing in place, please ensure that the Temperature Station can receive the 915MHz signal from the temperature transmitter at the positions that you wish to place them. CARE AND MAINTENANCE: Extreme temperatures, vibrations and shocks should be avoided as these may cause damage to the unit and give inaccurate forecasts and readings. Do not use solvents or scouring agents as they may mark the LCD and casings. Furthermore, fix all parts in place where the units are adequately protected against moisture and rain. [. . . ] The unrestricted disposal of electronic waste may do harm on public health and the quality of environment. As stated on the gift box and labeled on the product, reading the "User manual" is highly recommended for the benefit of the user. This product must however not be thrown in general rubbish collection points. The manufacturer and supplier cannot accept any responsibility for any incorrect readings and any consequences that occur should an inaccurate reading take place. [. . . ]